Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both in com-
ponentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to
expedite any request for service information or spares (in case of problems encountered either during, or subsequent to, installation).
This information will assist in providing prompt and accurate advice from your coemar service centre.
Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to
come.
Open the packaging and ensure that no part of the equipment has suffered damage in transit. In case of damage to the equipment,
contact your carrier immediately by telephone or fax, following this with formal notification in writing.
Ensure the packaging contains:
1
ISPOT 1200 EB
1
instruction manual
2
cam-lock projector supports
The
ISPOT 1200 EB
should be transported in its original packaging or in a coemar approved flight case.
In order to manufacture a suitable flight case, we recommend the following simple procedure to be followed, which will stop the
articulated movement of the
ISPOT
1200 EB
.
Fire prevention:
1.
ISPOT 1200 EB
utilises a Philips
MSI1200W/s
or Osram
HMI 1200W/s lamp;
the use of any alternative lamp is not
recommended and will null and void the fixture’s warranty.
2
Never locate the fixture on any flammable surface.
3
. Minimum distance from flammable materials: 0,5 m.
4
. Minimum distance from the closest illuminable surface: 2 m.
5.
Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any doubt.
6.
Connect the projector to mains power via a thermal magnetic circuit breaker.
Preventing electric shock:
1.
When connecting the
I-Spot 1200 EB
to mains power, the instructions in this manual should be followed carefully.
2.
The level of technol
ogy inherent in the -Spot 1200 EB
requires the use of specialised personnel for all service applica-
tions; refer
all work to your authorised
coemar
service centre.
3.
A good earth connection is essential for proper functioning of the projector. Never operate the unit without proper earth
connection.
4.
High voltage is present in the internals of the unit. Isolate the projector from mains supply prior to performing any function
which involves touching the internals of the unit, including lamp replacement.
5.
The mains cable should not come into contact with other cables.
Always handle the mains cable and all other cables connected to the unit with extreme caution.
Never handle the
I-Spot 1200 EB
with wet hands.
6.
Ensure that the mains voltage applied is the recommended voltage for the projector.
7.
Never install the projector in locations which may be exposed to rain, high humidity or which lack suitable air flow.
Protection against ultraviolet radiation:
1.
Never turn on the lamp if any of the lenses, filters, or the carbon fibre housing is damaged; their respective functions will only
operate efficiently if they are in perfect working order.
2. Never look directly into the lamp when it is operating.
Safety:
1.
The projector should always be installed with bolts, clamps, and other fixings which are suitably rated to support the weight of
the unit.
2.
Always use a secondary safety chain of a suitable rating to sustain the weight of the unit in case of the failure of the primary fix-
ing point.
3.
The external surface of the unit, at various points, may exceed 150°C. Never handle the unit until at least 10 minutes have elapsed
since the lamp was turned off.
4.
Always replace the lamp if any physical damage is evident.
5.
Never install the fixture in an enclosed area lacking sufficient air flow; the ambient temperature should not exceed 35°C.
6.
A hot lamp may explode. always wait for at least 10 minutes to elapse after the unit has been turned off prior to attempting to
replace the lamp.
Always wear suitable hand protection when handling the lamp.
Protection rating against penetration by external agents:
1.
The fixture is classified ordinary device ; its protection grade against penetration by external agents,solid or liquid, is IP 20
3. Important safety information
2. Transporation
1. Packaging
5
Summary of Contents for ISPOT 1200 EB
Page 2: ......
