manualshive.com logo in svg

Coemar DR1, Instruction Manual

Share
Download
Coemar DR1 Instruction Manual Download Page 16

movement sensor (CON 3)

Via the 

con3

connector you may test the correct operation of the movement sensors within the projector as well as of the con-

nectors and cabling associated with movement and the precision of the encoder wheel. Locate the movement sensor within the fix-
ture and attach it to the 

con3

connector of the 

sensor test PCB

. By moving the encoder wheel, the display of the 

DR1

should

display either 

CW 

or 

CCW 

depending upon the direction of the movement. The display will also provide information about the

state of the double encoder sensor, showing either 

GOOD 

(correct) or 

BAD 

(incorrect). If this is not the case, the sensor will requi-

re replacement. Additionally, you may also test the connector and cabling by isolating the cable which connects the sensor to the
motherboard and attaching one end to the sensor provided with the kit and the other end to the 

con3

connector of the 

sensor

test PCB

and then moving the encoder wheel. By doing so, you should register a change in the display on the 

DR1

. Should this

not be the case, the cabling is damaged and will require replacement.

1.

Attach the 

CON3

connector to the temperature sensor of your projector.

2.

Press the 

remote

button on the display of the 

DR1

; the display will show 

D.REM

3.

By using the 

+

or 

-

buttons, scroll to the 

SENS

option.

4.

Press the 

enter

button; via the 

+

or 

-

scroll to 

CON3

5.

Press the 

enter

button; via the 

+

or 

-

scroll to 

MOVE

. Moving the encoder wheel, which is located internally in the projector

alongside the pan and tilt motors, in either a clockwise or anticlockwise direction will cause the display of the 

DR1

to display

either 

CW 

or 

CCW

. The display will also provide information about the state of the double encoder sensor, showing either 

GOOD

(correct) or 

BAD 

(incorrect). Should the display show 

BAD

, check the cabling and connectors and the distance between the

two sensors on the encoder wheels, which may be too close or too far apart.

6.

You should repeat the operation for all the movement sensors within the unit.

CW/CCW

rotation direction

GOOD/BAD

position

AOO1

D . R E M

SENS

CON3

connector 3

MOVE

movement

sensor

☞

enter

☞

remote

☞

+/-

☞

enter

☞

+/-

☞

enter

☞

+/-

con3

Position sensor

33

English 

Summary of Contents for DR1




















Reviews:

No comments

Brands by name

Popular brands

Load more brands