background image

5

ca2051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.

1

BLUE/GREEN

2ND UNLOCK OUTPUT ( - )

This wire provides a ( - ) 200mA output upon the second press of unlock. This
output is used unlock the remaining passenger doors when the system is set up
for driver priority unlock.

10 Pin Main Harness

3

WHITE/RED

PARKING LIGHT INPUT

4

WHITE

PARKING LIGHT OUTPUT

Locate the parking light output wire at the vehicle’s light switch.

Verification: This wire registers positive voltage when the parking lights
are turned on.

Positive switching Parking Lights:

Connect the WHITE/RED wire to a 15 Amp max fused battery source.

Connect the WHITE wire to the parking light output wire.

Negative switching Parking Lights:

Connect the WHITE/RED wire to a good chassis ground.

Connect the WHITE wire to the parking light output wire.

2

BLACK/WHITE

ILLUMINATED ENTRY OUTPUT ( - )

This wire provides a  ( - ) 200mA output for 30 seconds when the system is
disarmed capable of driving relays.

Locate the vehicle’s dome light or pin switch wire.

Verification:  This wire will register positive voltage or ground when the
vehicle's dome light is turned ON.

Summary of Contents for ca 2051

















Reviews: