Code Alarm ca 2051 Installation Manual Download Page 11

Page: 11 / 16

Chirp Delete - User Accessible

System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.

Turn the ignition ON then OFF.

Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.

Feature Bank 1 -

3 Chirps

Transmitter Programming

Refer to transmitter programming.

Feature Bank 2 -

4 Chirps

Security Control

1 LED Flash

2 LED Flash

3 LED Flash

4 LED Flash

5 LED Flash

1 Silent Choice

OFF

Feature Bank 3 -

5 Chirps

Output Control

1 LED Flash

2 LED Flash

3 LED Flash

4 LED Flash

5 LED Flash

1 Extended Lock Pulse

1 Second

3.5 Seconds

1 Second Lock,
Double Pulse
Unlock

30 Second
Lock, Double
Pulse Unlock

Double Pulse
Lock, 1 Second
Unlock

2 2nd Unlock Output

2nd Unlock

Factroy Disarm

3 Ignition Controlled Locks

OFF

Lock and
Unlock

Lock Only

Unlock Only

Trunk Output Timing
Red / White Output

Push and Hold

10 Seconds

20 Seconds

Latched until
IGN ON

Latched ON
until Button
Press

5 Horn Output Timing

16mS

10mS

30mS

40mS

50mS

Summary of Contents for ca 2051















Search results

Summary of Contents for ca 2051

Reviews:

Brands by name

Popular brands

Code Alarm ca 2051, Installation Manual

Search results

Summary of Contents for ca 2051

Reviews:

Brands by name

Popular brands