5
-
10
220S Owner’s Manual
COBALT
220S
BOWRIDER
S
ECTION
5
Zippers
When zippers are new, they can be more difficult to
zip than when “used.” Zip carefully without forcing.
They will loosen with use. Keep the zippers clean.
A zipper lubricant may be used to help new zippers
and to maintain long trouble-free service. The most
vulnerable part of the zipper is where they start.
Use care when starting zipper to prevent damage.
Snap Fasteners
Fasteners should be unsnapped as close to the
button as possible. Never remove canvas by pulling
roughly on one edge of the material. This can
damage the canvas and the fasteners. To prevent
snaps from becoming difficult to unsnap, keep them
clean and use lubricants such a small amount of
Vaseline
®
, Chapstick
®
, WD-40
®
, silicone spray, etc.
The most common recommendation is to rub
candle wax or paraffin around the stud or inside the
socket. Whichever method is used, make sure you
clean up any excess so the lubricant does not stain
the canvas or any other surfaces it may contact.
WINDSHIELD
To keep the windshield clean, use a non-abrasive
glass cleaner applied with a soft cloth. Do not use
harsh detergents, solvents, chemicals or dry cloths.
These items will scratch the surface.
BILGE
Keep the bilge area as clean as possible. Use a
vacuum cleaner to remove debris from the bilge
area. Oil and greasy dirt will accumulate over time
and normally can be removed using soap and
water. If necessary, consult your authorized Cobalt
dealer for recommendations on special bilge
cleaning and absorption products.
MARINE GROWTH
If marine growth is a problem in your boating area,
it may be necessary to apply anti-fouling paint to
the hull to slow growth and prevent gelcoat
damage. Consult your authorized Cobalt dealer for
recommendations.
STATIONARY ARCH WITH
AWLGRIP TOPCOAT
Your Cobalt boat may be equipped with a fixed,
stationary arch with Awlgrip Topcoat.
It is difficult for dirt, grime and grease to adhere to
Awlcraft 2000 Topcoat; however, over time, a
buildup of dirt, grease and other contaminants can
cause the finish to appear dull.
Maintaining your topcoat with a combination of
Awlwash and Awlcare will deliver the best results.
The mirror-like gloss can be easily maintained by
following these simple rules.
DO:
1. Wash the surface regularly with Awlwash 73234
and water. Regular cleaning will avoid buildup,
which can slowly attack the topcoat,
prematurely aging the coating.
2. Use only mild solvents to remove stubborn
stains. Awlprep T0008, mineral spirits, xylene,
kerosene and diesel fuel are acceptable for use
on Cobalt’s topcoat.
Apply solvents with soft, clean cloths. Wipe up
solvent quickly. Do not allow solvent to dry on the
surface or puddle and soak into the surface.
Wash these areas with mild detergents and
water to remove solvent residue.
3. Always thoroughly rinse all surfaces with fresh
water after cleaning with detergents or solvents.
Latent solvent residue can attack the topcoat,
while detergent residue will attract dirt.
4. Use distilled white vinegar and hot water to
remove stubborn salt stains.
5. Use Awlcare 73240 by hand only to remove
stubborn diesel soot stains.
Summary of Contents for 220S
