Coast Spas CURVE APEX Owner'S Manual Download Page 6

OWNER’S MANUAL

 

2021

 

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

DANGER:

  Risk  of  Injury. 

The suction fittings in this Curve Spa are 

sized to match the specific water flow created by the pump. Should 
the  need  arise  to  replace  the  suction  fittings  or  the  pump,  be  sure 
that the flow rates are compatible.  Never operate  the Curve  Spa if 
the  suction  fittings  are  broken  or  missing.  Never  replace  a  suction 
fitting with one rated less than the flow rate marked on the original 
suction fitting.

DANGER: 

Risk  of  Accidental  Drowning. 

Do not allow children to 

be  in  or  around  the  spa  without  adult  supervision.  Keep  the  spa 
cover on and locked when not in use. See instructions enclosed with 
the cover for locking procedures.

DANGER: 

Risk  of  Electrical  Shock.

 The electrical supply for 

this product must include a suitably rated switch or circuit breaker to 
open  all  ungrounded  supply  conductors  to  comply  with  section 
422-20  of  the  National  Electrical  Code,  ANSI/NFPA  70.  The
disconnect must be readily accessible and visible to the Curve Spa
occupant  but  installed  at  least  5  feet  (1.5  m)  from  the  Curve  Spa
water.

READ, FOLLOW AND SAVE THESE INSTRUCTIONS 

a) A green colored terminal or a terminal marked G, Gr, Ground,

Grounding or the symbol * is located inside the supply terminal
box  or  compartment.  To  reduce  the  risk  of  electric  shock,  this
terminal  must  be  connected  to  the  grounding  means  provided
in  the  electric  supply  service  panel  with  a  continuous  copper
wire equivalent in size to the circuit conductors that supply this
equipment.

b) At  least  two  lugs  marked  “Bonding  Lugs”  are  provided  on  the

external  surface  or  on  the  inside  of  the  supply  terminal  box
compartment. To reduce the risk of electric shock, connect the
local  common  bonding  grid  in  the  area  of  the  Curve  Spa  to
these terminals with an insulated or bare copper conductor not
smaller than No. 6 AWG.

c) All  field-installed  metal  components  such  as  rails,  ladders,

drains  or  other  similar  hardware  within  5  feet  (1.5  m)  of  the
Curve  Spa  shall  be  bonded  to  the  equipment  grounding
buss with copper conductors not smaller than No. 6 AWG.

WARNING: 

To Reduce the Risk of Injury.

 

The water in a Curve Spa 

should never exceed 104 °F (40 °C). Water temperatures between 
100 °F (38 °C) and 104 °F (40 °C) are considered safe for a healthy 
adult.  Lower  water  temperatures  are  recommended  for  young 
children and when Curve Spa use exceeds 10 minutes.

Since  excessive  water  temperatures  have  a  high  potential  for 
causing  fetal  damage  during  the  early  months  of  pregnancy, 
pregnant  or  possibly  pregnant  women  should  limit  Curve  Spa 
water temperatures to 100 °F (38 °C). If pregnant, please consult 
your  physician  before  using  a  Curve  Spa.  Before  entering  the 
Curve Spa, the user should measure the water temperature with 
an  accurate  thermometer  since  the  tolerance  of  water 
temperature regulating devices may vary as much as +/- 5 °F (2 °
C). Persons suffering from obesity or a medical history of heart 
disease, low or high blood pressure, circulatory system problems 
or diabetes should consult a physician before using a Curve Spa.

CAUTION: 

Risk  of  Hyperthermia.

 

Hyperthermia  occurs  when 

the  internal  temperature  of  the  body  reaches  a  level  several 
degrees above the normal body temperature of 98.6 °F (37 °C). 
The  symptoms  of  hyperthermia  include  drowsiness,  lethargy, 
and  an  increase  in  the  internal  temperature  of  the  body. 
Prolonged  immersion  in  hot  water  may  induce  hyperthermia. 
A  description  of  the  causes,  symptoms,  and  effects 
of hyperthermia are as follows: 

Unawareness of impending hazard;

Failure to perceive heat;

Failure to recognize the need to exit Curve Spa;

Physical inability to exit Curve Spa;

Fetal damage in pregnant women; and

Unconsciousness and danger of drowning.

WARNING:

  Children  should  not  use  Curve  Spas  without  adult

supervision.

WARNING: 

Do  not  use  Curve  Spas  unless  all  suction 

guards are installed to prevent body and hair entrapment.

WARNING:

  People  with  infectious  diseases  should  not  use a 

Curve Spa. 

WARNING:

To  avoid  injury,  exercise  care  when  entering  or 

exiting the Curve Spa.

WARNING:

 Do not use drugs or alcohol before or during the use 

of Curve Spa to avoid unconsciousness and possible drowning. 
The use of alcohol or drugs can greatly increase the risk of fatal 
hyperthermia in Curve Spas.

WARNING:

 Pregnant or possibly pregnant women should consult 

a physician before using a Curve Spa.

WARNING:

 Water temperature in excess of 38 °C (100 °F) may 

be  injurious  to  your  health.  Before  entering  the  Curve  Spa, 
measure the water temperature with an accurate thermometer.

CURVE

 

COLLECTION

Summary of Contents for CURVE APEX


























































Reviews: