OWNER’S MANUAL
2021
5
4
Imperial Calculation: Add sodium bromide which has a
guarantee of at least a 98% active ingredient, such as
BromiCharge per 100 US gallons of water. Example, if your
spa holds 300 US gallons of water, add 3.6 lbs of sodium
bromide (3 X 1.2 lb).
Note:
Your selling dealer can tell you
how much water your spa holds (in liters or gallons).
MAINTENANCE MODE
Maintenance Mode keeps the bromine bank levels at a stable
and acceptable range when the spa is not being used.
Maintenance mode is the “everyday” mode and is automatically
ON when the system is activated.
Press and hold the Program key for 2 seconds to change the
maintenance mode level.
Use the Up and Down keys to adjust the maintenance level,
ranges from 1 to 50.
Finding and setting the right maintenance level will keep the
residual bromide level between 3 and 5 PPM (the recommended
range). Once the proper maintenance level is determined, keep
the same setting unless the spa conditions change (change in
water temperature, spa location etc.).
BOOST MODE
The Boost Mode should be activated every time you use your
spa. Boost mode increases the bromine generation rate to attack
pollutants in the water and helps rebuild the necessary residual
bromine in the water after each use of the spa.
If water quality is not good after use, only boost level should be
adjusted, not the maintenance level.
Press the Boost key once while in maintenance mode to start a
boost, or to adjust boost settings.
Use the Up and Down keys to adjust the boost level, ranges
from 1 to 8.
Note:
Boost levels depend on the number of bathers using the
spa. We recommend you validate the Boost level after
each use to determine the ideal boost level for all numbers of
bathers.
IN.CLEAR INSTRUCTIONS
See video: http://www.inclear.ca/inclearstartupprocedure
For more information: http://www.inclear.ca/inclearwater
CLEAN THE SPA
It's important to completely clean the spa to remove all residues
accumulated on the surface and inside or around the jet area.
After draining the spa, use spa cleaning products only. Household
cleaners contain additives such as phosphates which may affect
the bromine production.
TDS (TOTAL DISSOLVED SOLIDS) CHECK
Check the TDS (Total Dissolved Solids) of the water you'll use to
fill the spa. Verifying the TDS range can be done by your spa
selling dealer. The TDS range should be within 50 and 400 PPM.
When you're certain the water is within the proper TDS range, fill
your spa. If the TDS is higher than 500 PPM, ask your spa dealer
for additional information to help reduce initial TDS. DO NOT use
water from a "Salt Water Softener" system. Make sure there is
adequate flow and that no airlocks are trapped in the unit's
plumbing. If airlocks are formed, start the pump and follow the
instructions in the owner’s manual.
A
DJUST WATER CHEMISTRY IN THE SPA
Proper chemical maintenance of a spa is essential for the health of
bathers. Maintaining the quality of the spa water within these
specified values will enhance your enjoyment of the spa and
prolong the life of the In.Clear system. For best results, adjust to
the following water chemistry parameters. Check these
parameters periodically.
Calcium hardness (TH): between 150
and 200 PPM Total Alkalinity: between 100 and 120 PPM pH:
between 7.2 and 7.8.
Water chemistry should be balanced before
adding sodium bromide into the water. It's essential that the water
chemistry parameters are within the proposed range to obtain
optimal system performance. vHigh Calcium Hardness may lead to
faster calcification of the electrolytic plates.
ADD SODIUM BROMIDE (SUCH AS BROMICHARGE)
Water temperature between 32° and 38° C (90° and 100° F) helps
dissolve sodium bromide and facilitates the adjustment of the
maintenance level. Start the pump on high speed to allow water to
circulate and slowly add sodium bromide uniformly in the spa by
simply pouring it from the container. Metric Calculation: Add 0.143
kg of sodium bromide which has a guarantee of at least a 98%
active ingredient, such as BromiCharge, per 100 L of water to
attain 1400 ppm TDS value (Total Dissolved Solids).
Example, if your spa holds 1200 L of water, add 1.72 kg of sodium
bromide (12 X 0.143 kg).
CURVE
COLLECTION