Coast Spas Classic Series, Owner'S Manual

Page: 22 / 32

22
The Main Menu
Time-of-Day
Be sure to set the Time-of-Day Setting the time-of-day is im-
portant for determining filtration times and other background
features. “Set Time” will appear on the display if no time-of-day
is set in the memory. On the Settings Screen, select the Time-of
-Day line. On the Time-of-Day screen, simply select the Hour,
Minutes, and 12/24 Hour segments. Use the Up and Down But-
tons to make changes.
Note: This only applies to some systems: If power is inter-
rupted to the system, Time-of-Day will be maintained for several
days.
Jets
The Spa Screen shows all available equipment to control, as
well as other features, like Invert. The display shows icons that
are related to the equipment installed on a particular spa model,
so this screen may change depending on the installation. The
icon buttons are used to select and control individual devices.
Some devices, like pumps, may have more than one ON state,
so the icon will change to reflect the state that the equipment is
in. Below are some examples of 2-speed Pump indicators.
If the Spa has a Circ Pump, a Circ Pump Icon will appear to indi-
cate its activity, but outside of Priming Mode, the Circ Pump
cannot be controlled directly.
Note: The icon for the pump that is
associated with the heater (Circ or P1 Low) will have a red glow
in the center when the heater is running.
Settings
The Settings Screen is where all programming and other spa
behaviors are controlled. This screen has several features that
can be acted on directly. These features may include Temp
Range, Heat Mode, Hold, and Invert Panel. When one of these
items is selected, it will toggle between two settings. All other
menu items (with an arrow pointing to the right) go to another
level in the menu.
Dual Temperature Ranges (High vs. Low)
This system incorporates two temperature range settings with
independent set temperatures. The specific range can be select-
ed on the Settings screen and is visible on the Main Screen in
Priming the Pumps
As soon as the Priming Mode screen appears on the panel, se-
lect the “Jets 1” button once to start Pump 1 in low-speed and
then again to switch to high-speed. Also, select the other pumps,
to turn them on. The pumps should be running in high-speed to
facilitate priming. If the pumps have not primed after 2 minutes,
and water is not flowing from the jets in the spa, do not allow the
pumps to continue to run. Turn off the pumps and repeat the pro-
cess. Note: Turning the power off and back on again will initiate a
new pump priming session. Sometimes momentarily turning the
pump off and on will help it to prime. Do not do this more than 5
times. If the pump(s) will not prime, shut off the power to the spa
and call for service. Important: A pump should not be allowed to
run without priming for more than 2 minutes. Under NO circum-
stances should a pump be allowed to run without priming beyond
the end of the 4-5 minute priming mode. Doing so may cause
damage to the pump and cause the system to energize the heat-
er and go into an overheat condition.
Exiting Priming Mode
The system will automatically enter the normal heating and filter-
ing at the end of the priming mode, which lasts 4-5 minutes. You
can manually exit Priming Mode by pressing the “Exit” button on
the Priming Mode Screen. Note that if you do not manually exit
the priming mode as described above, the priming mode will be
automatically terminated after 4-5 minutes. Be sure that the
pump(s) have been primed by this time. Once the system has
exited Priming Mode, the top-side panel will display the Main
Screen, but the display will not show the temperature yet, as
shown below. This is because the system requires approximately
1 minute of water flowing through the heater to determine the
water temperature and display it.
Navigation
Navigating the entire menu structure is done by touching the
screen. When a text item is shown in white on the main screen, it
is selectable. The menu selections on the right side of the screen
can be selected. Select one of these to enter a different screen
with additional controls. Most menu screens time out and revert to
the main screen after 30 seconds of no activity. The only item
that can be changed on the left side of the Main Screen is the Set
Temperature. Touch either the set temperature line or the water
temperature to go to the Set Temperature screen.
Luxury Topside Quick Reference Card