manualshive.com logo in svg

Cloud CDI-46, Installation And Setup Manual, Page: 4 / 28

Share
Download
Cloud CDI-46 Installation And Setup Manual Download Page 4

CDI-46 Installation and Setup Guide V1.3

4

Installation

Mechanical fitting and internal connections

Fit the CDI-46 card within the 46-120 host unit according to the instructions below:

1. 

Disconnect the 46-120 from the AC mains.

2. 

If the 46-120 is installed in an equipment rack, disconnect all audio and control wiring, remove the unit from the rack and 

place on a convenient flat surface.

3. 

Remove the top cover (10 screws) and orientate the unit with the rear panel towards you.

4. 

Remove the adhesive label covering the empty connector holes from the rear panel.

J2

(below sub-board)

LINE INPUT SUB-BOARD

CON21

CON22

CON25

CON23

CON13

REAR LH SECTION OF 

46-120 MAIN PCB

NOT TO SCALE – FOR 

COMPONENT LOCATION 

PURPOSES ONLY

REMOVE M3

 

SCREW

REMOVE M3

 

SCREW

REMOVE

 

JUMPERS

REMOVE

 

JUMPERS

J7

J10 - J13

J1

 

J17

 

J5

5.  Refer to the 46-120 main PCB layout diagram above. Note that there are several jumpers on the PCB which will be not 

readily accessible once the CDI-46 card is installed (i.e., the card will need to be removed to access them). Therefore 

installers should ensure that these jumpers are set as required BEFORE fitting the CDI-46.
Note that J10 to J13 MUST be removed for the CDI-46’s Digital Paging Interface to operate correctly.  If the CDI-46 is being 

installed purely for remote control purposes (and not paging), they can stay in place.

Summary of Contents for CDI-46





























Reviews:

No comments