Cloud CDI-46 Installation And Setup Manual Download Page 22 | Manualshive

Page: 22 / 28

background image

CDI-46 Installation and Setup Guide V1.3

22

Documents

Selecting

Documents

, then

Control Protocol

opens a new browser tab, displaying a PDF version of the CDI-46’s Serial

Control Protocol.

This is a comprehensive document containing full details of all aspects of the CDI-46’s serial control protocol. See also “Abridged

command set” on page 24

.

Music Mute

The browser interface also provides indication of Music Mute status. The nature of the indication depends on whether you are
logged in as a User or an Installer.
When an external mute command is applied to the 46-120’s Music Mute port, the browser interface becomes unavailable to a
User while the mute is active. The current page is greyed-out and the page heading banner changes from blue to red:

If you are logged in as an Installer, control remains available, but the page heading banner changes colour to red, with the word

Mute displayed:

«
...
20
21
22
23
24
...
»

Summary of Contents for CDI-46





























Reviews:

No comments

Related manuals for CDI-46

Brand: Tanco Pages: 72

Brand: HABYS Pages: 16

Brand: Acterna Pages: 72

Brand: ACE INSTRUMENTS Pages: 15

Brand: Wave Fitness Pages: 15

Brand: ACCU-CHECK Pages: 104

Brand: Gardner Bender Pages: 8

Brand: NARIKA Pages: 2

Brand: Abus Pages: 12

Brand: Yamaha Pages: 16

Brand: Qlight Pages: 4

STOMAMED COL-160

Brand: Orliman Pages: 12

Brand: Unika Pages: 8

Brand: TECshow Pages: 22

Brand: ICON Pages: 24

Brand: Handicare Pages: 26

Brand: Pilz Pages: 12

Brand: ABS Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands