background image

 

M03Q40G6-03 30/07/08 

pag 

32 

SECONDARY SET POINT – ECO 

A secondary set point can be used with different levels to the “normal” set point. 
It is normally set to give lower energy consumption with respect to the comfort setting:  

• 

The SECONDARY SUMMER set point is higher than the SUMMER setting. 

• 

The SECONDARY WINTER set point is lower than the WINTER setting. 

It can be set according to individual requirements. 

• 

Secondary summer set-point parameter 29  

• 

Secondary winter set-point parameter 30 

 
 

It can be activated from the keyboard, supervisor unit or the remote control. To change it using the remote control refer to the 
ELECTRIC WIRING paragraph. 
If the 3-way valve option for sanitary water is present, the 2° set point in heating can be activated by service/remote keypad 
with par 49 =1 
 

par Description 

Meaning 

value 

49 

Comando2°Set 

2° set point mode control by parameter 

 

MAINTENANCE  

This way, the plant can be kept within the operating limits even when the unit is OFF or on STANDBY, for example during the 
weekend or the night-time. 
Periodically the system activates the circulation pump, measures the water temperature and activates the compressor, if 
required, to take the water temperature to the set-point level. 

 

• 

Summer maintenance set-point   par 42 

• 

Winter maintenance set-point 

par 43 

 

This function is activated by parameters 44 (activate summer maintenance level) and 45 = 1 (activate winter maintenance 
level). 
 

DUAL CONTROLS FOR TEMPERATURE – RADIANT PANELS  

With the optional kit, a mixed plant can be controlled: 

 

Fan coil (with the set-points seen above) 

 

Radiant panels (with specific radiant set-points) 

The radiant set point can be determined in different ways, for further details see the ELECTRICAL CONNECTIONS section. 

 

FUNCTIONING WITH ETHYLENE GLYCOL  

The units foreseen to function with glycoled water come out from the premise with standard parameters. 
After having added glycol ethylene to water, the technician will properly set the plant. 
 

% Ethylene glycol 

Parameter to modify 

10 % 

20 % 

30 % 

40 % 

32 

Summer set point 

- 4 

- 10 

- 18 

77 

Antifreeze heater set 

- 2 

- 7 

- 13 

- 21 

80 

Antifreeze alarm 

- 2 

- 7 

- 13 

- 21 

84 

Antifreeze pre-alarm threshold 

- 1.5 

- 6.5 

- 12.5 

- 20.5 

 

Summary of Contents for WSH-EE 101





















































Reviews: