Clinton 84100 User Manual Download Page 8 | Manualshive

Page: 8 / 11

Clinton 84100 User Manual Download Page 8

METAL

Metal frame and stirrups (if applicable) should be cleaned according to facility antimicrobial standards and dried
with a clean soft cloth. Never use abrasive cleaners or scrubbing implements on painted surfaces.

UPHOLSTERY

Clinton uses only premium vinyl for upholstery, however, care should be taken when cleaning to ensure that the
upholstery or color is not affected by the cleaning agent. Use only mild cleaning agents on upholstery. Clinton
recommends using a 1 to 1 mix of ammonia and water or a 1 to 4 mix of bleach and water. Rinse thoroughly
with clean water and pat surface dry. This is not a guarantee and does not relieve the user from responsibility of
the proper and safe use of all cleaning agents. Test on inconspicuous area prior to using any cleaning agent on
upholstery's visible surface. Certain cleaning agents can be harmful to the surface.

WARNING:

Always clean surfaces that come in contact with pathogens or infectious materials

according to standard procedures of your particular healthcare or therapy facility. Although Clinton
recommends a cleaning solution it is not a guarantee that it will meet with your facility’s standards
or state, federal and local standards for treatment and cleaning of areas and equipment that may be

exposed to pathogens and infectious materials.

PERIODIC INSPECTION

• Inspect all electrical cords and connections for damage or wear.
• Check that all fasteners are in place and securely fastened.
• Make certain that the hi-lo function of the table is in proper working condition.
• Check to ensure that the table has remained level.

BACKREST CYLINDER REPLACEMENT

(Models 84200 & 84430 only)

Remove cotter pin. Then remove
the slide-out pin. Position tab
located on the adjustment bar
against cylinder pin.

Align holes in cylinder bracket with holes in table bracket by
adjusting the angle until the holes line up. Install slide-out pin
through holes and replace cotter pin.

Finished view of cylinder assembly.

The backrest cylinder is replaceable in the field by following these simple directions below.

Cylinder Pin

Tab

PREVENTIVE MAINTENANCE & PARTS REPLACEMENT

CLEANING

8

«
...
6
7
8
9
10
...
»

Summary of Contents for 84100












Reviews:

No comments