ClimbTech EAL12NC-72Y-C13 Operation And Instruction Manual Download Page 7 | Manualshive

Page: 7 / 12

background image

12” Ø or Smaller

DANGEROUS LOADING CONDITIONS

Warning:

This anchorage connector is designed to deform under fall arresting forces. Do not make

connections that may allow the anchorage connector to disengage the anchorage when deformed.

This includes but is not limited to scaffolding rosettes smaller than 12” in diameter.

Warning:

Connections that allow fall arresting forces to act in the opening direction of the gate are

not permitted.

Transverse/Side loading tested using ANSI Z359.12 fixturing in static and dynamic load conditions.

Dynamic Testing performed according to ANSI Z359.18 Type A requirements.
Minimum Static Breaking Strength: 3600-lbf.

TRANSVERSE LOADING

«
...
5
6
7
8
9
...
»

Summary of Contents for EAL12NC-72Y-C13













Reviews:

No comments

Related manuals for EAL12NC-72Y-C13

Brand: Rabe Pages: 65

Brand: GBC Pages: 8

Brand: KAPSCH Pages: 57

Brand: XTA Pages: 29

Brand: vc999 Pages: 59

Brand: Qtx Pages: 3

Brand: Saferoad Pages: 24

Brand: Eaton Pages: 21

Brand: NANO Pages: 4

Brand: IBEX Pages: 4

Brand: IDS Pages: 2

Brand: Quark-Elec Pages: 2

Brand: Jackson Pages: 2

Brand: Vag Pages: 10

Cell Saver Elite+

Brand: Haemonetics Pages: 230

LUNAQUA Classic LED

Brand: Oase Pages: 16

Brand: GE Pages: 2

Brand: K-SPORT Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands