EN
- 5 -
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The accessory automatically engages.
Operating machine
Press the brush motor switch (2) (to the right or left). The motor
starts.
If you raise the bar (7) slightly, the machine moves to the right (D).
If you lower the bar, the machine moves to the left (D).
If you keep the bar in its central position, the machine works on the
spot.
After use
Squeeze the shaft adjustment handle (5) and shift the bar (7) into
its vertical position.
Then tip the machine onto its wheels (9) and press the brush
motor switch (2) briefly. The accessory (11) disengages.
Remove the plug from the power socket and wind the electric
cable around the handle bar (1) and cable hook (8).
Thorough cleaning the easy way
For thorough cleaning, equip your machine with the following accesso-
ries:
-
Solution tank (13)
-
Scrubbing brush (11) or drive plate with pad.
Fasten the tank to the mounting (14).
Slide the outlet hose (12) onto the water connector (16).
Fill the tank (13). Then fit the brush or drive plate with pad.
Control the flow of liquid with the tank lever (15) by pulling the
lever (15) upwards.
Vacuum the dirty wash solution a section at a time with a water
extractor.
Shampooing thoroughly and efficiently
For shampooing, equip your machine with the following accessories:
- Solution tank; 0.3 Perlon shampooing brush or pad for textile
floorcoverings.
The working procedure is in principle the same as for thorough
cleaning.
Start the machine with the shampooing brush dry.
Meter a small amount of liquid until the bristles are saturated with
foam.
Run the machine with the rotating brush from right to left or vice-
versa.
⇒
Immediately after this, run the machine in the same way
in the reverse direction, but with an overlap of about a quarter of
the strip already treated (E.)
Only then run the machine in a spiral pattern over the shampooed
strips.
⇒
In doing so, work both strips at the same time (F.)
During shampooing it is highly advisable to immediately remove
the dirt-laden foam a section at a time with a water extractor.
Assembly instructions for Spray unit
Fit the holder for the spray can to the bar (7) with the holder point-
ing upwards and, when viewed from the operating side, to the left
(G).
Hook the spray can’s tongue onto the holder, pivoting the holder
back until the ball catch engages.
Then slide the spring clip over the shaft adjustment unit (7).
Attach the box on the right or left as desired (H).
Point the universal-jointed hose in the desired direction.
Routine cleaning
For routine cleaning, equip your machine with the following accesso-
ries:
- Spray unit, drive plate for pads, pad for F8/F3 low speed or Spray
unit, drive plate for pads, pad for F12/F8 high speed
Fill the spray can with the desired product.
Fit the drive plate with the desired pad.
Start the machine.
When you pull the Spray unit lever a few times the cleaning agent
is sprayed onto the floor. Now start cleaning immediately until a
shine is produced.
We advise cleaning the surface in relatively small areas at a time.
The machine is ideal for cleaning with polymer dispersions. The
coating’s resistance to foot traffic and general wear and tear is
preserved. Streaks and marks are easier to remove.
Polishing with F12/F8 high speed
For polishing, equip your machine with the following accessories:
-
Drive plate for pads, white pad
-
Fit the drive plate with the pad.
Then start the machine.
Service
•
•
•
•
•
•
•
•
For repairs, please contact your specialist wholesaler or one of the
service shops.
You will be expertly and quickly served.
Servicing instructions
the following instructions must always be observed
When cleaning and servicing the machine, replacing parts or when
changing over to a different function, switch off the drive and re-
move the plug.
The power supply lead must not be damaged by driving over it,
crushing, tugging etc.
Check the power supply lead regularly for signs of damage.
The machine must not be used if the power supply lead is not in
perfect condition.
When using or replacing the power supply or equipment supply
leads, use only those specified by the manufacturer.
When replacing the plug-and-socket connectors of power supply or
equipment supply leads, splash protection and mechanical
strength must be assured.
