EN
- 6 -
•
•
•
•
•
When transporting the machine in lifts, put the shaft/bar in a verti-
cal position so that it cannot catch on the lift walls.
The shaft/bar is automatically secured against recoil by the pat-
ented shaft/bar adjustment unit.
Only the spray and cleaning agents suitable for the machine’s
purpose may be used.
Never use highly flammable, combustible, toxic, health-hazardous,
corrosive or irritant substances.
Repairs, including the fitting of spray agent lines and hoses, may
only be carried out by approved customer service shops or by
specialists in this field who are familiar with all the relevant safety
regulations.
Storage
•
•
Remove brush/pad driver from machine and neatly coil cord
around cord hook and handle.
Store the machine in a dry place and in normal room conditions
(not below under 0
°
C).
Trouble Shooting
Problem Cause
Solution
Machine does not operate
Faulty power cord.
Contact Service Center.
Tripped
circuit
breaker
Wait
10
min. till machine cooled down and try again.
Faulty machine wiring.
Contact
Service
Center
Faulty
motor.
Contact
Service
Center
Capacitor
burned
out
.
Contact Service Center
Machine operates with a wobble
Soiled Pad.
Replace Pad
or jerky motion.
Improper pad/brush for application.
Change to proper pad/brush
Pad driver/brush not installed correctly.
Remove and reinstall pad driver/brush
Pad/brush
unevenly
worn.
Replace
pad/brush
Pad not properly centered on pad driver
Remove and reinstall pad driver
Machine circuit breaker trips
Heavily soiled pad/brush
Clean or replace pad/brush
continuously.
Improper pad/brush for application
Change to proper pad/brush
Defective
circuit
breaker.
Contact
Service
Center
Worn carbon brushes in motor.
Contact Service Center
Technical specifications
F3 low speed
F8 high speed
F12 Duo speed
A.C. motor
230 V: 50 Hz
230 V; 50 Hz
230 V, 50 Hz
Rated power
1000 W
1100 W
1200/1500 W
Max. amp draw
5,5 A
5,5 A
5,2 / 8,1 A
Brush (rpm)
165
400
170 / 340
Brush (mm)
430 430 430
Working height (mm)
250 250 250
Working weight
31 kg
31 kg
37 kg
Protection class
lPx4 lPx4 IPx4
Belt-driven
x x x
Sound pressure level LPA
59db (A)
59db (A)
65db
Weighted acceleration value
1.05 m/sec2
1.05 m/sec2
1.05 m/sec2
DECLERATION OF CONFORMITY FOR MACHINERY (Directive 89/392/EEC, Annex II, sub A)
Model: F3,F8,F12
Machine nr.: MF122004, MF122904, MF32004, MF32904, MF82004, MF82904
Tennant N.V.
Herewith declares, on our own responsibility, that the machinery
Adress: Industrielaan 6, 6405 AB - is in conformity with the provisions of Directive 89/392/EEC, 73/23/EWG and 89/336/EWG
P.O. Box 6, 5400 AA Uden-The Netherlands - The following standards and normative documents have been applied:
Uden/Netherlands, 20-12-06
EN 60335-1 (ed.3);am1;am2, 60334-2-67(ed2);am1, EN60355-1:94+A1:96+A12:96+A13:98+A14:
98+A15:00+A2:00+A16:01,EN60355-2-67:98+A1:00, EMC:CISPR 14-1:00+A1:01,CISPR 14-2:01,
ICE61000-3-2:00,IEC61000-3-3:94+A1:01,EN55014-1:00+A1:01,EN 55014-2:97+A1:01,
EN61000-3-2:00, EN 61000-3-3:95+A1:01
-----------------------------------------------------------------
Richard van de Hoogen - Technical Support Engineer
