ClearView IPD-81A Operation Manual Download Page 26

Page: 26 / 143

4.1.1 Function of Play

The function of play is shown as in Figure 4-2 and Figure 4-3.

Figure 4-2

Figure 4-3

Parameter

Function

①

Play

When you see this button, it means pause or not played record. Click on this
button, switch to normal play status.

②

Stop

Click this button to stop playing.

③

Play by

frame

Click on this button to go to next frame.

Note:

You shall pause record when you use this function.

④

Slow

Click on this button to play slowly.

⑤

Quick

Click on this button to play quickly.

⑥

Silent

When this button displays, it means audio is silent. Click on this button to switch

back to normal.

⑦

Volume

Click on left mouse to adjust volume.

⑧

-1 Fisheye

Click this button and fisheye device can adjust display mode according to
different installation mode during the process of playback.

⑧

-2 Rule Info

Click the button and it will playback and display intelligent rules and object
detection box if the video is equipped with intelligent rule info after the function is
enabled, it is off by default.

Summary of Contents for IPD-81A
















































































































































Search results

Summary of Contents for IPD-81A

Reviews:

Related manuals for IPD-81A

Brands by name

Popular brands

ClearView IPD-81A, Operation Manual

Search results

Summary of Contents for IPD-81A

Reviews:

Related manuals for IPD-81A

Brands by name

Popular brands