ClearSpan Super Moo-Tel Building 38' Wide Assembly Manual Download Page 27

Page: 27 / 47

CLEARSPAN

™

SUPER MOO-TEL

Revision date: 03.16.12

TWIST-OF-THE-WRIST ASSEMBLY

Gather the parts:
• Aluminum channel (#102570) and drive handle

(#102480)

• Gearbox (#103496) and gearbox double drive

(#102717)

• Mounting plate (#103544) and bearing assembly

(#102569)

• Threaded rod (#FAK26), 3/8" nuts (#FALB04B) and

washers (#FAME08B)

•  CC6212 fabric clips (Use half for each side.)
•  5/16'' machine bolts (FAG336B) and 5/16" nuts
•  Drill and drill bits

The Twist-of-the-Wrist Assembly is designed to roll up

a portion of the sides of the cover. The following steps

describe the installation of one assembly.
1. At the end where you will attach the gearbox, drill a

5/16" hole through the cover conduit 1/2" from the end

of the conduit.

2. Insert a tubing adapter into the conduit and align

the holes of the adapter with the drilled holes in the

conduit.

3. Select one aluminum channel and drill a 3/8" hole

through the channel approximately 2" from the end and

attach a threaded rod to the channel using a 3/8" nut

on each side of the channel.

3/8" Nut

Threaded

Rod

4. Position the channel along the rafter at the desired end

of the building where the Twist-of-the-Wrist assembly

will be located. Place the lower end of the channel

an inch off the ground to allow free movement of the

channel during the operation of the roll-up cover.

5. Secure the upper end of the channel by drilling a 3/8"

hole through the end rafter and attach as shown. The

lower end of the channel will "float" and is not attached.

NOTE:

Install a 3/8" flat washer between the 3/8" nut

and the end rafter.

Frame shown for illustration.

6. Select the bearing bracket and attach the bearings as

needed. (In some instances, the bearings may come

already attached.) Assemble as follows if needed:

Single bearings are attached to the sides of the bracket

and double bearings to the middle portion of the

bracket. Use 1/4" hex bolts and locknuts as needed.

Install a flat washer on both sides of each bearing to

insure proper operation of bearings and the assembly.

Install the longer bolts with bearings on the side of the

bracket that has the two holes. Install these

before

installing the double bearing assembles. See the

figures below.

7. For the spacers on the long bolts, insert a 5/16" nut

over each bolt.

These nuts are used as spacers only.

5/16" Nut

1/2"

Flat

Washer

Nut

8' Channel

Aluminum Channel

End Rafter

Flat Washers

Threaded

Rod

3/8''

Nut

TOP VIEW

End panel

not shown

for clarity.

Summary of Contents for Super Moo-Tel Building 38' Wide
















































Search results

Summary of Contents for Super Moo-Tel Building 38' Wide

Reviews:

Related manuals for Super Moo-Tel Building 38' Wide

Brands by name

Popular brands

ClearSpan Super Moo-Tel Building 38' Wide, Assembly Manual

Search results

Summary of Contents for Super Moo-Tel Building 38' Wide

Reviews:

Related manuals for Super Moo-Tel Building 38' Wide

Brands by name

Popular brands