ClearSpan Super Moo-Tel Building 38' Wide Assembly Manual Download Page 23

Page: 23 / 47

CLEARSPAN

™

SUPER MOO-TEL

Revision date: 03.16.12

END PANEL INSTALLATION

The following procedure describes installing an end panel.

NOTE:

The end wall shown in the diagrams that follow may

differ in design and size. The steps to install the basic end

panel are the same despite these obvious differences.

Required parts include:
•  End panels
•  102921B washers
•  FA4482B Tek screws

Complete these steps to install a typical end panel:
1. Spread an end panel out on the ground and center the

end panel as needed.

2. With the proper lift (or ladders) positioned inside the

frame and with assistance, pull the end panel up and

over the top of the end rafter. Square the end panel on

the end frame and verify that the bottom edge is in the

desired position.

ATTENTION:

Allow 16"-18" at the bottom of the end

panel to remain on the ground after the top edge of the

panel is secured to the rafter.

3. With the lower edge of the end panel in the desired

position, temporarily secure the top end of the panel to

the backside of the end rafter in a few places using Tek

screws and washers.

ATTENTION:

For buildings longer than 48', do not

screw through the straps used to stretch the main cover

from end-to-end. View shows the outside of end wall.

DO NOT ATTEMPT

TO PULL THE END

PANEL INTO POSITION

ON WINDY OR STORMY

DAYS!

5. Once the lower edge is secured as desired, move

to the top edge of the panel, remove the temporary

screws, and pull the panel up and over the end rafter to

stretch it into position.

6. Install Tek screws and washers to secure the panel to

the end rafter.

Space screws every 12" or so along the inside of the

rafter. Do not screw through any straps.

7. After installing both end panels, return to the door

end(s) of the frame and cut the opening for the roll-up

door.

4. Move to the bottom of the end panel and pull the end

panel edge under the end wall tubing so approximately

6"-12" is showing on the inside of the building.

NOTE:

If you cannot pull the material under the base

rail, stretch the panel end-to-end and face screw the

panel from the outside to the base rail using Tek screws

and washers.

Cut the panel to fit around frame members if desired.

Dashed line shows

where to install the Tek

screws and washers

View shows the inside or

backside of the end wall.

Summary of Contents for Super Moo-Tel Building 38' Wide
















































Search results

Summary of Contents for Super Moo-Tel Building 38' Wide

Reviews:

Related manuals for Super Moo-Tel Building 38' Wide

Brands by name

Popular brands

ClearSpan Super Moo-Tel Building 38' Wide, Assembly Manual

Search results

Summary of Contents for Super Moo-Tel Building 38' Wide

Reviews:

Related manuals for Super Moo-Tel Building 38' Wide

Brands by name

Popular brands