ClearSpan Super Moo-Tel Building 38' Wide Assembly Manual Download Page 16

Page: 16 / 47

CLEARSPAN

™

SUPER MOO-TEL

Revision date: 03.16.12

PREPARE MAIN COVER

Gather the parts:
• Pipe 1.66" x 99" swaged
• Pipe 1.66" x XX" plain: The XX refers to the length of the plain pipe needed to reach the end of the frame and to

complete the conduit. Consult the Side Profile Diagram in the Quick Start section of these instructions for your

building to identify this pipe length.

• Main cover
• Tek screws

Assembly Procedure

NOTE:

When handling the main cover and setting it in position, do not pull on the end straps. They will pull out of the

cover.

Do not insert any cover conduit into a cover pocket that includes a pre-installed strap.

WARNING:

To prevent damage to the cover and to prevent serious personal injury, DO NOT attempt to install the

main cover on windy days.

1. Assemble two main cover conduits. Start each cover conduit assembly with one plain pipe and add swaged pipes to

arrive at the length of the frame.

This cover conduit is identical to the on-center length of the shelter.

Once assembled,

the cover conduits are inserted into the side pockets of the main cover. The conduits are used to tighten and secure

the main cover to the frame.

Consult the Side Profile Diagram in the Quick Start section for pipe identification.

2. After assembling the cover conduits, locate the main cover and unfold it on a clean, smooth surface near the frame.

Unfold the main cover with the inside surface facing up and the straps positioned at the front and back of the frame.

a. Locate all sections of pipe needed to assemble

the cover conduit.

b. Insert the swaged end of each pipe into the

plain end of another pipe until the conduit is

assembled.

c. Secure each pipe joint with a Tek screw.
d. Use duct tape to tape over each Tek screw.

3. Align the cover ends with the front and back of the shelter and insert one cover conduit into each side pocket of the

main cover.

NOTE:

Shelter shown above may be of a different style or length than actual shelter.

4. Continue by pulling the cover up and onto the frame.

Roll-Up Conduit

Pockets at the

cover edge.

Cover Ends w/Strapping

Cover

Conduit in

Conduit

Pocket

Stretch Hem Pockets

(See note above.)

STEP 3

FRONT

BACK

To prevent damage or possible injury or both, do

not attempt to pull cover on a stormy or windy

day or when such conditions are expected.

Summary of Contents for Super Moo-Tel Building 38' Wide
















































Search results

Summary of Contents for Super Moo-Tel Building 38' Wide

Reviews:

Related manuals for Super Moo-Tel Building 38' Wide

Brands by name

Popular brands

ClearSpan Super Moo-Tel Building 38' Wide, Assembly Manual

Search results

Summary of Contents for Super Moo-Tel Building 38' Wide

Reviews:

Related manuals for Super Moo-Tel Building 38' Wide

Brands by name

Popular brands