background image

Lithium Power Supply User Manual 

 

 

 

 

   

Page 

31 

   

   

   

Interface 

Each LPS has a service interface that allows a qualified technician to analyse any failures and the general 
condition of the LPS. The service port also allows for firmware updates.

 

Power conservation 

When the LPS is not in use it will enter a low power state. In this state the LPS keeps power consumption 
very  low  to  avoid  unnecessary  discharge  of  the  battery.  The  LPS  can  be  reactivated  through  the  power 
switch or by applying a charge source to either the 230VAC input or the 12VDC input. 

10. Warranty 

CAUTION & WARNING:  
DO NOT USE OR ATTEMPT TO USE THIS PRODUCT UNTIL YOU HAVE READ THIS USER'S MANUAL IN 
ITS ENTIRETY. IMPROPER INSTALLATION OR USAGE OF THIS DEVICE MAY BE HAZARDOUS AND MAY 
CAUSE DAMAGE TO OTHER ELECTRICAL EQUIPMENT AND WILL VOID WARRANTY.  
 
Clayton Power warrants, to the original purchaser only, for a period of 24 months from the date of 
purchase, that the Clayton Power device will be in good working order when properly installed and 
operated as described in this manual.  
If the device fails within this time period under normal use, Clayton Power will, without charge, at the place 
of Clayton Power's choosing, repair or replace the device - with new or reconditioned parts or a new or 
reconditioned device as Clayton Power deems necessary.  
 
This warranty is not valid in cases of:  
Usage against the recommendations of this manual.  
Usage in applications outside of general automotive, solar, industrial or marine applications without the 
agreement of Clayton Power.  
Device modification or repair without written authorization from Clayton Power.  
Reverse polarity, excessive overloading, general abuse, neglect, wear & tear, ingress of liquids (water, oil, 
acid, or otherwise), foreign objects, lightning strikes, over or under voltage, RFI/EMI, etc. 
 
Obtaining Warranty Service  
To obtain warranty service, please contact the outlet at which you purchased your product. Do not contact 
Clayton Power directly. For warranty service provide the following:  

 

Proof of purchase  

 

The unit model number  

 

The unit serial number   

 

A brief description of the application and problem including any failure codes displayed on the unit. 

 

Contact your Clayton Power dealer for an authorization number prior to dispatch - do not send 
without authorization. Once this number has been obtained, please carefully pack your unit and 
send (freight paid) to the Clayton Power dealer. 

 

Please note that the unit contains Lithium batteries and must be shipped as dangerous goods 
according to UN3480 (Lithium-Ion Batteries) 

 
Copyright 
The information contained within this document remains the sole property of Clayton Power. No part of this 
document may be copied or reproduced in any form or by any means, and the information contained within 
is not to be communicated to third parties, without the prior written consent of Clayton Power. 

Summary of Contents for LPS

































Reviews: