background image

4

Important! Before Fitting!

If at all possible, do steps 1-2 one to 

two days before first use. This is to 

allow the adhesive on the hook and 

loop to cure.

Important! Club Cars 1983-07!

If you have a 1983-2007 Club Car 

you will need to install an adapter 

bar after step 2. Please refer to the 

instructions with the adapter bar. 

If the adapter bar is not included 

with this enclosure you can get 

one from your retailer or from 

Classic Accessories.

TOOLS NEEDED:

• Scissors
• Small wood block or 

piece of cardboard

1. Apply adhesive hook strips 

to your car front roof posts.

Remove your enclosure from the storage bag 
and locate the plastic bag holding the adhesive 
backed hook strips. Remove the two longest 
32" strips. 

If you have a folding windshield skip to step 1b. 

1a. For non-folding windshields:

Attach one of the 32" strips to the 

outside

 

(not 

the front) 

of one of your cars' front roof posts 

on either side of the windshield. Hold the strip 
vertical and peel an inch or so of the adhesive 

backing from the top end. 
Align the strip along the 
roof post with the top of the 
strip just where the post 
straightens out below the 
roof line. Slowly peel off the 
backing as you press the strip 
down the post. 

If there is a 

plastic windshield channel 
attached to the post cut 
the strip at the edge of the 
plastic and start a new piece 
on the aluminum post.

Using a small wood block 

or piece of cardboard press 
the strip firmly down along 
the entire length of the post.

Now put the other 32" strip 

on the opposite roof post.

1b. For folding 

windshields:

If you have a folding windshield you can follow 
the instructions above in 1a except you need 
to cut the adhesive backed hook strip to allow 
space for where the rubber windshield 
fittings attach.

Fold your windshield up and mark the top and 

bottom of where the rubber fitting cinches on the 
roof post.

Cut the 32" strip into individual pieces to go 

above and below your marks and then attach 
them to the roof posts.

Wait one to two days for the glue to cure 

before proceeding.

Fairway 

Deluxe 3-Sided Golf Car Enclosure

Assembly and Care Instructions

Summary of Contents for Fairway Deluxe 3-Sided Golf Car Enclosure









Reviews: