Classe Audio CP-800 Page 2 Owner'S Manual Download

Page: 2 / 54

Classé marks the “CE” symbol indicating compliance of this device with the EMC (Electromagnetic
Compatibility) and LVD (Low Voltage Directive) standards of the European Community.

Classé complies with the European Parliament and Council Directive 2002/96/EC concerning Waste Electrical
and Electronic Equipment (WEEE). This product must be appropriately recycled or processed in accordance with
these directives. Consult your local waste disposal authority for guidance.

Classé products are designed and manufactured to comply with the Restriction of Hazardous Substances (RoHS)
as stated in the European Parliament and Council Directive 2002/95/EC.

NOTICE

All of us at Classé take extreme care to ensure that your purchase will remain a prized investment. We are proud to inform you

that all Classé components have been officially approved for the European Community (CE) mark.

This means that your Classé product was subjected to the most rigorous manufacturing and safety tests in the world. The CE

mark certifies that your purchase meets or exceeds all European Community requirements for manufacturing consistency and

consumer safety.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including interference that may cause undesired operation. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the

equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna;

• Increase the separation between the equipment and the receiver;

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s

authority to operate the equipment.

This product incorporates copyright protection technology that is protected by U.S. patents ad other intellectual property

rights. Reverse engineering or disassembly is prohibited.

The information contained in the manual is subject to change without notice. The most current version of this manual will be

posted on our web site at http://www.classeaudio.com.

Summary of Contents for CP-800























































Search results

Summary of Contents for CP-800

Reviews:

Related manuals for CP-800

Brands by name

Popular brands

Classe Audio CP-800, Owner'S Manual

Search results

Summary of Contents for CP-800

Reviews:

Related manuals for CP-800

Brands by name

Popular brands