background image

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

DAILY

1. Before use, drain water from the airline filter and compressor.

2. If no airline lubricator or mini oiler is used, ensure that oil is applied to the 

tool on a daily basis through the air inlet connection. Run a few drops of oil 
through the tool before use. It may be entered into the tool air inlet, 
(ensuring the strainer is clear), or into the hose at the nearest connection to 
the air supply.

3. This procedure should be repeated after every two to three hours of use, or 

at the start of the working day.

4. Keep the body of the tool clean and free from debris.

WEEKLY

1. Check the air inlet screen filter for 

blockage and clean if necessary.

CLEANING & OVERHAUL

1. Grit or gum deposits in the tool 

may reduce efficiency.

2. After extensive use, remove the 

inlet screen filter and flush out the 
mechanism with gum solvent oil or 
an equal mixture of CLARKE air-
line oil and paraffin. Allow to dry before use.

3. If the tool still runs erratically or becomes inefficient, and the air supply is of 

good quality, it may be necessary to dismantle the air motor and replace 
worn or damaged parts. You may prefer to take the tool to your CLARKE 
dealer if internal maintenance is required.

4. The air tool may be dismantled by unfastening the bolts and removing the 

rear cover prior to replacing any worn or damaged parts.

5. While is a dismantled state, it may be desirable to grease the hammer 

mechanism and applying a small amount of good quality bearing grease.

• This may be better left to your CLARKE dealer.

WARNING: MAKE SURE THAT THE WRENCH IS DISCONNECTED FROM THE 
AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE 
PROCEDURES.

Summary of Contents for X-Pro CAT198

















Reviews: