background image

6

SAFETY SYMBOLS

ALWAYS: 

Read this manual. Understand all warnings and 

instructions before operating this equipment.

DANGER:

 Risk of fire or explosion. Shut off engine before 

adding fuel. Keep work area free of combustible materials. 
Do not spray flammable liquids.

DANGER:

 Risk to breathing. Engine exhaust fumes can kill. 

For outdoor use only. Work in a well ventilated area.

WARNING: 

Risk of injection or severe injury. Do not direct 

discharge stream at persons or animals. Keep clear of nozzle. 
This machine is to be used only by qualified operators.

WARNING:

 Risk of spray injury. Spray can propel objects. 

Always wear ANSI approved Z87.1 Safety Glasses.

WARNING:

 Risk of chemical burn. Never spray acids, corrosive 

or toxic chemicals. Use only cleaners formulated for power 
washers.

WARNING:

 Risk of electrocution. Never direct spray toward 

any electrical device or electrical outlet.

WARNING:

 R i s k   o f   u n s a f e   o p e r a t i o n .   K e e p   children away 

from this equipment. Gun kicks back. Hold with both hands.

WARNING:

 Risk of hot sur faces. Avoid contact with hot 

engine exhaust components. Don't allow hoses to contact 
the engine muffler during or after use.

Summary of Contents for Power Wash PLS190





























Reviews: