background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY PRECAUTIONS

Before using your compressor it is in your own interest to read and pay 
attention to the following safety rules:

1.

COMPRESSED AIR IS DANGEROUS 

- Never direct a jet of air at people or 

animals.

2. Do not operate your air compressor with any guards removed.

3. Electrical or mechanical repairs should only be carried out by a qualified 

electrician/engineer. If you have a problem, contact your local dealer, or our 
Service Department on 020 8988 7400

4. Before attempting any repair ensure pressure is expelled from the air receiver 

and disconnect from electrical supply.

5. Do not leave pressure in air receiver overnight or when transporting.

6. Do not adjust or tamper with any safety valves. The maximum working pressure 

of the compressor is clearly stated on the machine.

7. Exercise caution when transporting the machine to avoid tipping the machine 

over.

8. Do not operate in a wet/damp environment.

9. Locate your air compressor on a firm flat surface with AVMs and ensure an 

adequate supply of clean air is available to the pump unit.

10. Do not exert any strain on electrical cables and ensure that air hoses are not 

tangled or wrapped around machinery etc.

11. The cylinder head and delivery pipes of your compressor become quite hot 

during operation. Do not touch. After switching off remember to leave an 
adequate cool-down period before touching.

12. Ensure that any equipment/tool used in conjunction with your compressor has 

a safe working pressure exceeding the output pressure of the machine.

13. When disconnecting air hoses or other equipment from your compressor 

ensure that the air supply is turned off at the machine outlet and expel all 
pressurised air from within the air hose and other equipment attached to it.

14. If using your compressor for paint spraying:

• Never spray close to any source of flame or heat.

• Always ensure that the spraying area has adequate fresh air ventilation.

• Hazardous paints require special apparatus (see paint manufacturers 

recommendations).

15. Never let people operate the compressor unless they have had the necessary 

training.

16. Permanently installed pipework systems should be designed and installed by a 

competent engineer.

Summary of Contents for PE11C50

















Reviews: