background image

10

OPERATION

When first using the machine, please use
the following procedure.

1.

Select LOW range, by moving the
Lever, adjacent to the Emergency
Stop, fully to the ‘L’ position.

2.

Push the emergency OFF switch cover
button (fig.2) upwards in direction of
arrow. This will allow the cover to spring
outwards, releasing the OFF button.

3.

Start the machine by turning the rotary
ON/OFF, variable speed switch, slowly

Ensure the work area is clean and tidy and all tools and accessories etc., are removed
and stored safely, before plugging the machine into the electric supply.

Switch the power ON. At this point, the  green indicator lamp on the switch panel on the front
of the machine, will illuminate, indicating that power is being supplied to the machine.

clockwise to mid position, and allow to run for a minute or two
before winding up to full speed, then allow to run for a further two minutes.

4.

Switch OFF by turning the rotary switch fully anticlockwise, then move
the Hi-Lo range lever to the ‘H’ - high position, and repeat the process.

NOTE: In case of emergency, hit the switch cover quickly. The cover will
latch down and the motor will be switched OFF.

The machine will not start when the emergency switch cover is closed.

If the emergency switch is used to switch OFF, when the rotary ON/OFF
switch in the ON position, the machine will not start again when the
emergency switch is released. The amber warning lamp will also illuminate.

The rotary switch must first be turned OFF then turned ON again to start the machine.

Once the machine has been ‘run up’ check to ensure that the machine is secure on the
bench or board, and check again to ensure the post is secure by attempting to tighten the
post securing nut at the rear of the machine using the 36mm spanner provided.

Fig.3

Fig.2

Fig.4

A.  Drilling

The machine is provided with a drill
chuck and morse taper shank - Fig.4.

Insert the taper shank up into the
spindle, sharply.

CAUTION. Take extreme care not to
damage the taper in any way. Any
burr or irregularity  will render it
unserviceable until it is properly
repaired using a grind stone.
Professional advice should be sought.

Fig.5

Pull off the spindle draw bolt cover from the head (see Parts ID, Fig-C on page
8s) and insert the draw bolt . Screw it into the end of the taper shank and
tighten using the spanner provided - see Fig.5.

Summary of Contents for CMD300

























Reviews: