background image

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY PRECAUTIONS

WORK AREA

1. Keep work area clean and well lit. Cluttered and dark areas invite 

accidents.

2. DO NOT operate power tools in explosive atmospheres, such as in the 

presence of flammable liquids or gases. Power tools can create sparks 
which may ignite the fumes.

3. Keep children and bystanders away while operating a power tool. 

Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. AVOID body contact with earthed or grounded surfaces such as pipes, 

radiators, ranges or refrigerators. There is an increased risk of electric shock 
if your body is earthed or grounded.

2. DO NOT expose power tools to rain or wet conditions. Water entering a 

power tool will increase the risk of electric shock.

3. When operating a power tool outdoors, use an extension cord suitable for 

outdoor use. Use of a cord suitable for outdoor use reduces the risk of 
electric shock.

PERSONAL SAFETY

1. ONLY hold the tool using the handles when in use. DO NOT attempt to use 

the tool with one hand.

2. Stay alert, watch what you are doing and use common sense when 

operating a power tool. DO NOT use a power tool while you are tired or 
under the influence of drugs, alcohol or medication. A moment of 
inattention while operating power tools may result in personal injury.

3. ALWAYS use safety equipment. Safety equipment such as dust mask, non-

skid safety shoes and hearing protection used for appropriate conditions 
will reduce personal injuries.

4. AVOID accidental starting. Ensure the switch is in the off position before 

connecting to the power supply. 

WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL 
INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/
OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED 
BELOW REFERS TO YOUR DEMOLITION HAMMER.

Summary of Contents for 6479509

















Reviews: