Clarke 6479504 Operation & Maintenance Instructions Manual Download Page 12

Page: 12 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

FAULTFINDING

Problem

Possible Cause

Remedy

Tool will not operate

No power supply

Check supply & rectify as
necessary

Switch is faulty

Consult your CLARKE
dealer

Fuse blown

Check & replace if
necessary

Motor is faulty

Consult your CLARKE
dealer

Motor runs but drill bit
does not move.

Drill fastening not tight

Secure drill bit

Drive gear broken

Consult your CLARKE
dealer

Heavy internal sparking

Faulty motor

Consult your CLARKE
dealer

Worn brushes

Consult your CLARKE
dealer

Motor becomes hot

Unduly heavy use

Reduce the force applied
to the drill bit. Let the tool
do the work

Air vent have become
blocked

Clean out the air vents
using compressed air or
clean with a dry cloth

Low supply voltage

Ensure supply voltage is
correct. If an extension
cable is used, ensure it is
the correct rating and is
fully unwound

Excessive vibration.

Drill bit bent or not
mounted correctly

Check and rectify

Machine bearings worn

Consult your CLARKE
dealer

Summary of Contents for 6479504

















Search results

Summary of Contents for 6479504

Reviews:

Related manuals for 6479504

Brands by name

Popular brands

Clarke 6479504, Operation & Maintenance Instructions Manual

Search results

Summary of Contents for 6479504

Reviews:

Related manuals for 6479504

Brands by name

Popular brands