Clarke 6015610 Operation & Maintenance Instructions Manual Download Page 11 | Manualshive

Page: 11 / 28

background image

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY SYMBOLS

The following safety warning symbols are displayed on the machine.

NOTE:

Further safety warnings on the machine label carry their own

explanations.

Read instruction
manual before use.

Danger! Arc rays

Recycle unwanted
materials in accordance
with WEEE directive.

Danger! Harmful fumes

Wear suitable welding
gloves

Do not weld near
flammable or
combustible materials

Danger! Risk of electric
shock.

Caution! Hot surfaces.

Magnetic Field may inter-
fere with pace-makers

When using this welder
always use a welding
helmet.

«
...
9
10
11
12
13
...
»

Summary of Contents for 6015610





























Reviews:

No comments

Related manuals for 6015610

Brand: Harman Kardon Pages: 2

Brand: Cal-Royal Pages: 4

Brand: KEF Pages: 12

Brand: EasyPro Pages: 8

Brand: Easylift Pages: 127

Brand: Geberit Pages: 49

Brand: Nelson Pages: 18

Brand: Nelson Pages: 150

Water Jet Lightning

Brand: Oase Pages: 28

Brand: Oase Pages: 9

Brand: Yamaha Pages: 7

Brand: MAHA Pages: 23

Brand: ABICOR Pages: 16

Brand: BSM Pages: 17

Brand: BRAVILOR BONAMAT Pages: 76

Brand: JBL Pages: 8

Brand: ADEMCO Pages: 40

Brand: Valx Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands