background image

2

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Cement Mixer.

Before attempting to use this product, please read this manual thoroughly and 
follow the instructions carefully. In doing so you will ensure the safety of yourself 
and that of others around you, and you can look forward to your purchase 
giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 
months from the date of purchase. Please keep your receipt which will be 
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or 
tampered with in any way, or not used for the purpose for which it was 
intended.

Faulty goods should be returned to their place of purchase, no product can 
be returned to us without prior permission. This guarantee does not effect your 
statutory rights.

SPECIFICATION

Max Drum capacity

134 Litre

Max Mixing Capacity

100 Litre

Drum Speed

23 rpm

Weight

60 kg

Dimensions: Length x Width x Height

1380 x 1100 x 620 mm

Power Cable Length

3 m

IP Rating

IP44

Sound Pressure

74.3 dB(A)

Sound Power Measured

90.0 dB LWA

Sound Power Guaranteed

90.0 dB LWA

Summary of Contents for 3400862

















Reviews: