background image

Reference Chart

You can use this chart to quickly identify and interpret the system’s chirp indications and LED flashes.

G1100 Installation Manual - Page 14

1 chirp  

arming 

normal arming

1 + 4 chirps

arming

door, hood, or trunk is open

Output

When

Status

No chirps

arming

Valet Mode is on 

LED double flashes

Valet Mode

Starter Defeat Activated

2 chirps

disarming 

normal disarming

3 chirps

disarming

Tamper Alert - system was triggered

1 LED flash

after Tamper Alert

door 

2 LED flashes

after Tamper Alert  

shock sensor 

3 LED flashes

after Tamper Alert

hood or trunk

4 LED flashes

after Tamper Alert

optional sensor

5 chirps

while Armed

Warn Away

4 chirps

with ignition key on

Sensor Test mode on

1 chirp 

in Sensor Test mode

impact detected

Multiple chirps 

1 minute after disarming

Automatic Rearming

(for 10 seconds)

LED flashing quickly

ignition key off

Passive Arming sequence started

Two chirps

ignition key off

Full Time System Diagnostics 

1 LED flash

after Full Time Sys. Diag.

door 

2 LED flashes

after Full Time Sys. Diag.   

shock sensor 

3 LED flashes

after Full Time Sys. Diag.

hood or trunk     

Continuous chirps

while Armed & Door Open

System Triggered
(Passive Arming Entry Delay Warning)

Summary of Contents for G1100
















Reviews: