background image

23

English

Problem

Check  the  wiring  to  the  camera  and  the  camera 
connection.

Check the wiring.

Replace with a fuse of the same amperage (5A)

Temperature  in  the  vehicle  is  below  -10°

C  or  over 

60°

C. Check to see that the temperature in the ve-

hicle is appropriate (around 25°

C).

No image is displayed.

Power does not turn on.

Color is washed-out.

Cause

Is camera connected 
properly?

Is power cable connected 
properly?

Is a fuse blown out?

Operating environment is 
inappropriate.

Measure

Horizental

Vertical

Video signal

Audeo signal

Frequency

Input signal

15.734KHz (NTSC)

60Hz (NTSC)

Composite video signal

MONO

Speaker

Language display selection

Operating temperature

Storage temperature

Dimension

0.5 Watt max.

8 Language

-10℃ to +60℃ / 14℉ to +140℉

-20℃ to +70℃  / -4℉ to +158℉

174(W) x 125(D) x 27(H) (mm) / 6.85(W) x 4.92(D) x 1.06(H) (inch)

Weight

480g / 16.93oz (monitor set only)

LCD Panel

Screen size

Resolution

Brightness

Voltage

Current

Power 
supply

7 inch

800(W) x 3(RGB) x 480(H)

450cd/m

2

DC12V-24V (10.8V-31.2V)

Approx. 900mA

 (DC14V, in case of connecing four sets of camera (CC-2000).

Contrast ratio

500:1

SPECIFICATION

11.

※ The design and specifi cations are subject to change without notice. 

TROUBLESHOOTING

10.

User controls

AV, MODE, ▲, ▼, MENU, POWER

15.625KHz (PAL)

50Hz (PAL)

Summary of Contents for CJ-7300G

























Reviews: