Page 31
Operating Instructions - Two Timer Models
OPERATING INSTRUCTIONS -
TWO TIMER MODELS
1.
After loading the dryer tumbler with water washed clothes load, proceed to close
the loading door. For better drying, do not load dryer with combination of
garments that twist.
2.
Turn the 60-minute drying timer to the desired drying time. The drying cycle
light will be on and indicate the drying. The light shuts off when drying time is
complete. (See figure 1 on page 30.)
3.
Turn the 15-minute cooling cycle timer to the desired cool down time.
(Note: Dryer will not
start unless some cooling time is selected!).
After the drying cycle is completed, then the
cooling cycle time will automatically operate. The cooling light will be on and indicate the
cooling of the clothes load. The light shuts off when cooling time is completed. (See figure 1 on
page 30.)
4.
Temperature Selector
- Select temperature per type of load being dried in the
dryer. (See figure 2 on page 30.)
High Heat
- Mixed and heavy fabrics, set dial to 195º F (91° C).
Normal
- Cottons and linens, set dial to 170º F (77° C).
Permanent Press Heat
- Poly knit synthetics, blends, lightweight fabrics, set
dial to 150º F (66° C).
Low Heat
- Delicate, sheer fabrics, easy-to-dry, set dial to 135º F (58° C).
5.
Thermometer
- Use this with your temperature selection. Teach yourself what
temperature is too hot or too cold. (See figure 3 on page 30.)
6.
Turn switch to start position. (See figure 1 on page 30.)
7.
Close the dryer door, but the basket will not rotate until the
PUSH-TO-
START BUTTON
is pressed. Press in the
PUSH-TO-START BUTTON
(approximately 2 seconds) until the dryer starts running and then release button.
(See figure 1 on page 30.)
What is happening to the drying operation:
a.
The fan motor will operate.
b.
The basket will rotate.
c.
The heat source will be energized.
d.
The heated air mix with the water washed clothes to
evaporate the moisture from the garments.
e.
The thermostats will function to maintain a safe
temperature throughout the drying cycle.
f.
The heat will be shut off and the motor will continue to
run to cool the dry load to a desired handling
temperature.
8.
When the drying timer completes its time, then the cooling timer will be
energized and the cooling light will be On. When the cooling light will stay
On and the End-of-Cycle light will be On. The End-of-Cycle light will go
off when the Start/Stop switch is turned to Off or O. At the end of the cool-
down cycle, the clothes load is dry.
9.
To shut the dryer Off, move the Start/Stop switch to Off or O position.
This switch is a safety switch to immediately stop the dryers operation.
Special Reversing Feature - Set the Reversing/Non-Reversing switch to
Reversing. See service manual for setting of time of each reversal. Reversing
of the basket is designed for loads that twist (example - bed sheets and large
mixed loads). Non-Reversing is for small or medium-size items that dont twist.
Summary of Contents for HD150.1
