background image

15

4

Operating instructions

Machine with start button

Sort the linen according to the type and required temperature of the linen. Empty

all pockets of the garments so that no garments can be damaged and no left articles

can cause damage to the machine. Turn sleeves of shirts, blouses inside out. It is

recommended to mix small and large items to enhance the drop of the linen during

the wash cycle and hence improve the wash quality. Wash loads of 

below 80%

of machine capacity 

can obstruct the proper functioning of the machine and can

damage the machine

. Overloading the machine can also lead to a bad wash result.

It is recommended to only use detergents with a “

foam-breaker

”. These are often

found  in  the  launderette  or  laundry  or  can  easily  be  found  in  retail  stores.

Recommended doses are mentioned on the detergent packing.

Overdosing of detergents can lead to reduced wash results and “overfoaming”

which can damage the machine.

Close the door

Fill the drum

On machines with a start button, the programmer can contain up to 100 programs

(0-99). The program number is displayed on the 

right display.

By pressing the SELECT-button (P), the next program will be displayed.

By pressing the ECO-button (E), the previous program will be displayed. By

keeping this button pressed, this function will be accelerated.

Remark

Select program “0” by keeping the SELECT-button pressed continuously for more

than 5 seconds.

Add detergent

Left compartment A:

Prewash (1st wash)

Central compartment B:

Main Wash (2nd wash)

Right compartment C:

Final Rinse (fabric softener)

Bottom compartment D:

Direct access to tub

Moderately soiled linen can be washed using the Economy Wash function, which

reduces the water level of washes and rinses by 

20%

, allowing savings of water

and energy.

Press the ECO-button 

during the wash cycle

  to  activate  the  economy  wash

function. The ECO-LED will light up.

At the 

end of the program

 the ECO-function will be automatically eliminated. If

the ECO-function is required in the following wash cycle as well, reactivate this

function by repeating the actions described above.

Economy Wash

Opening the door

Push the red button on the door handle to open the door.

Select program

Summary of Contents for CSHW35-HW55-164


































Reviews: