Cisco ONS 15454 M6 Installation Manual Download Page 85

Page: 85 / 164

NTP-G524 Install the Power Modules in the ONS 15454 M6 Shelf

This procedure installs the power modules in the ONS 15454 M6 system.

Purpose

#2 Phillips screwdriver

Tools/Equipment

•

NTP-G252 Install the ONS 15454 M6 Shelf , on page 24

•

NTP-G259 Open and Remove the Standard Door of the ONS 15454 M6
Shelf , on page 57

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, see the

Electrostatic Discharge and Grounding Guide

for Cisco CPT and Cisco ONS Platforms

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

The plug-socket combination must be accessible at all times because it serves as the main disconnecting
device.

Statement 1019

Warning

Procedure

Step 1

Complete the necessary task as applicable:

•

DLP-G569 Install the AC Power Module in the ONS 15454 M6 Shelf, on page 85

•

DLP-G757 Replacing 15454-M6-AC With 15454-M6-AC2 Power module, on page 88

•

DLP-G758 Replacing 15454-M6-AC2 With 15454-M6-AC Power module, on page 89

•

DLP-G570 Install the DC Power Module in the ONS 15454 M6 Shelf, on page 90

•

DLP-G737 Replacing 15454-M6-DC With 15454-M6-DC20 Power Module, on page 93

•

DLP-G738 Replacing 15454-M6-DC20 With 15454-M6-DC Power Module, on page 95

Step 2

Complete the

NTP-G256 Install Power and Ground to the ONS 15454 M6 Shelf , on page 100

Stop. You have completed this procedure.

DLP-G569 Install the AC Power Module in the ONS 15454 M6 Shelf

This task installs the 15454-M6-AC or 15454-M6-AC2 power module in the ONS
15454 M6 system.

Purpose

Installing the ONS 15454 M6 Shelf

NTP-G524 Install the Power Modules in the ONS 15454 M6 Shelf

Summary of Contents for ONS 15454 M6





































































































































































Search results

Summary of Contents for ONS 15454 M6

Reviews:

Related manuals for ONS 15454 M6

Brands by name

Popular brands

Cisco ONS 15454 M6, Installation Manual

Search results

Summary of Contents for ONS 15454 M6

Reviews:

Related manuals for ONS 15454 M6

Brands by name

Popular brands