Cisco ONS 15454 M6 Installation Manual Download | Manualshive

Page: 100 / 164

background image

NTP-G256 Install Power and Ground to the ONS 15454 M6 Shelf

This procedure installs power feeds and grounds the ONS 15454 M6 system.

Purpose

ANSI and ETSI:

• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver
• Screws
• Ground cable 13.3-mm² (#6 AWG) stranded
• Listed pressure dual-holes lugs suitable for #8 AWG copper conductors
• Wire cutters
• Wire strippers
• Crimp tool
• Fuse panel

ANSI only:

• Power cable (from fuse and alarm panel to assembly), #8 AWG, copper

conductors, 194 degrees F [90 degrees C])

• Wire wrapper

ETSI only:

• Power cable (from fuse panel to power modules), shipped with the ONS

15454 M6

• Two-hole grounding lug, shipped with the ONS 15454 M6

Tools/Equipment

•

NTP-G524 Install the Power Modules in the ONS 15454 M6 Shelf , on page
85

.

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, see the

Electrostatic Discharge and Grounding Guide

for Cisco CPT and Cisco ONS Platforms

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

To ensure safety of personnel and equipment, do not connect any power cables into the power module
until the module is completely installed into the chassis.

Statement 389

Warning

To reduce the risk of electric shock, switch on the power only after the power cord is completely installed
into the power module.

Statement 390

Warning

Installing the ONS 15454 M6 Shelf

100

Installing the ONS 15454 M6 Shelf

NTP-G256 Install Power and Ground to the ONS 15454 M6 Shelf

«
...
98
99
100
101
102
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands