Cisco ONS 15454 M6 Installation Manual Download Page 90 | Manualshive

Page: 90 / 164

background image

Always use the supplied ESD wristband when working with a powered ONS 15454 M6. For detailed instructions
on how to wear the ESD wristband, see the

Electrostatic Discharge and Grounding Guide for Cisco CPT and

Cisco ONS Platforms

.

Caution

Procedure

Step 1

Disconnect the power source and remove the power connections from the B-side power module (installed in
slot B).

Step 2

Unscrew the holding screw that secures the 15454-M6-AC2 power module.

Step 3

Pull the 15454-M6-AC2 power module clear from the ONS 15454 M6 chassis.

Step 4

Install the 15454-M6-AC power module as described in the

DLP-G569 Install the AC Power Module in the

ONS 15454 M6 Shelf, on page 85

Step 5

Install power on the 15454-M6-AC power module as described in the

NTP-G256 Install Power and Ground

to the ONS 15454 M6 Shelf , on page 100

While replacing the power modules, do not provision or install any line cards when the ONS 15454
M6 chassis is in the mixed power mode (with both 15454-M6-AC and 15454-M6-AC2 power
modules installed). Card provisioning and installation must be done only after both the slots have
the same type of power modules.

Note

Step 6

Perform steps 1 to 5 for the other power module (installed in slot A).

Step 7

Return to your originating procedure (NTP).

DLP-G570 Install the DC Power Module in the ONS 15454 M6 Shelf

This procedure installs the 15454-M6-DC, 15454-M6-DC20, or 15454-M6-DC40
DC power module in the ONS 15454 M6 system.

Purpose

#2 Phillips Dynamometric screwdriver

Tools/Equipment

•

NTP-G252 Install the ONS 15454 M6 Shelf , on page 24

.

•

NTP-G259 Open and Remove the Standard Door of the ONS 15454 M6
Shelf , on page 57

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, see the

Electrostatic Discharge and Grounding Guide

for Cisco CPT and Cisco ONS Platforms

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Installing the ONS 15454 M6 Shelf

90

Installing the ONS 15454 M6 Shelf

DLP-G570 Install the DC Power Module in the ONS 15454 M6 Shelf

«
...
88
89
90
91
92
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands