Cisco ONS 15454 M6 Installation Manual Download | Manualshive

Page: 24 / 164

background image

Bulk Chassis Flow, CFM

Deflector Configuration

Case

295.6

215.3

No deflectors

Side to Side

135.8

97.7

Inlet and Outlet

ETSI Front to Rear

258.6

187.7

Only Inlet

ETSI Front to Side

166.9

120.5

Inlet and Outlet

ANSI Front to Rear

268.6

193.5

Only Inlet

ANSI Front to Side

NTP-G252 Install the ONS 15454 M6 Shelf

This procedure installs the shelf.

Purpose

• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver
• ETSI only:

• Six M6 x 20 pan-head Phillips mounting screws

• ANSI only:

• Six #12-24 x 3/4 pan-head Phillips mounting screws

Tools/Equipment

NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454
M6 Shelves

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the
floor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip
over.

Statement 1048

Warning

This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations.

Statement 1045

Warning

Installing the ONS 15454 M6 Shelf

24

Installing the ONS 15454 M6 Shelf

NTP-G252 Install the ONS 15454 M6 Shelf

«
...
22
23
24
25
26
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands