Cisco MEM-NP16F Series Upgrade Manual Download Page 6

Page: 6 / 10

6 Upgrading the Flash EPROM Memory Card

Removing the Flash EPROM Memory Card

Follow these steps to remove the Flash EPROM card. (See Figure 3.)

Figure 3

Flash EPROM Memory Card Location

Step 1

Place the component tray in front of you as in Figure 3.

Step 2

Remove the two card mounting screws from the Flash EPROM card and set the screws
aside.

Caution

To prevent damaging the Flash EPROM card, handle it by the sides only.

Step 3

Holding the Flash EPROM card by its edges, pull straight up to lift the card out of its
connector. (See Figure 4.) The system-memory SIMMs will now be exposed.

FW1

FW2

EPROM card
cutaway view
96-pin EPROM
connector

EPROM card
mounting screw

LEDs

Boot ROMs

Module
mounting
screws

Token Ring module

Dual serial module

Ethernet module

EPROM card
mounting
screw

Module cutaway view
128-pin module connector

H4464

Module mounting
screw

Front

Module handle

LED

SOFTWARE UPDATE

ALLOWED

INHIBITED

J5 J6

Summary of Contents for MEM-NP16F Series











Search results

Summary of Contents for MEM-NP16F Series

Reviews:

Related manuals for MEM-NP16F Series

Brands by name

Popular brands

Cisco MEM-NP16F Series, Upgrade Manual

Search results

Summary of Contents for MEM-NP16F Series

Reviews:

Related manuals for MEM-NP16F Series

Brands by name

Popular brands