manualshive.com logo in svg

Cisco ME 3600X, Command Reference Manual

The Cisco ME 3600X is a versatile networking product that delivers exceptional performance and reliability. Ensuring seamless integration into your network infrastructure, this device offers advanced features and high-speed connectivity. Get started with this product effortlessly by downloading its user manual for free from manualshive.com and access comprehensive information to maximize its potential.

Share
Download
background image

 

-77

Cisco ME 3800X and ME 3600X Switch Command Reference

OL-28238-01

Chapter       

show interfaces transceiver

Examples

This is an example of output from the 

show interfaces 

interface-id 

transceiver

 

properties

 command:

Switch# 

show interfaces gigabitethernet0/1 transceiver properties

Diagnostic Monitoring is not implemented.

Name : Gi0/1

Administrative Speed: auto

Administrative Duplex: auto

Administrative Auto-MDIX: on

Administrative Power Inline: N/A

Operational Speed: 1000

Operational Duplex: full

Operational Auto-MDIX: on

Media Type: 10/100/1000BaseTX SFP

This is an example of output from the 

show interfaces transceiver dom-supported-list 

command:

Switch# 

show interfaces transceiver dom-supported-list

  

Transceiver Type           Cisco p/n min version  

                               supporting DOM     

------------------       -------------------------

DWDM GBIC                ALL                      

   DWDM SFP                 ALL                      

   RX only WDM GBIC         ALL                      

   DWDM XENPAK              ALL                      

   DWDM X2                  ALL                      

   DWDM XFP                 ALL                      

   CWDM GBIC                NONE                     

   CWDM X2                  ALL                      

   CWDM XFP                 ALL                      

   XENPAK ZR                ALL                      

   X2 ZR                    ALL                      

   XFP ZR                   ALL                      

   Rx_only_WDM_XENPAK       ALL                      

   XENPAK_ER                10-1888-03               

   X2_ER                    ALL                      

   XFP_ER                   ALL                      

   XENPAK_LR                10-1838-04               

   X2_LR                    ALL                      

   <output truncated>

This is an example of output from the 

show interfaces transceiver threshold-table

 command. Note that 

these are thresholds programmed into IOS software, and are NOT used to determine alarms.

Optical Tx     Optical Rx    Temp     Laser Bias    Voltage 

                                                    current               

             -------------  -------------  ------   ------------  ---------

 DWDM GBIC

Min1             -0.50        -28.50        0             N/A          4.50      

Min2             -0.30        -28.29        5             N/A          4.75     

Max2              3.29         -6.69        60            N/A          5.25     

Max1              3.50          6.00        70            N/A          5.50     

 DWDM SFP

Min1             -0.50        -28.50        0             N/A          3.00      

Min2             -0.30        -28.29        5             N/A          3.09     

Max2              4.30         -9.50        60            N/A          3.59     

Max1              4.50          9.30        70            N/A          3.70     

 RX only WDM GBIC

Min1              N/A         -28.50        0             N/A          4.50      

Min2              N/A         -28.29        5             N/A          4.75     

Max2              N/A          -6.69        60            N/A          5.25     

Max1              N/A           6.00        70            N/A          5.50     

 DWDM XENPAK

Min1             -1.50        -24.50        0             N/A          N/A       

Summary of Contents for ME 3600X





















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ME 3600X

D-Link xStack DGS-3420 Series How To Set Up preview
xStack DGS-3420 Series
Brand: D-Link Pages: 2
D-Link DXS-3600-32S Quick Installation Manual preview
DXS-3600-32S
Brand: D-Link Pages: 29
D-Link DWS-1008 User Manual preview
DWS-1008
Brand: D-Link Pages: 454
D-Link DWS-1008 Product Manual preview
DWS-1008
Brand: D-Link Pages: 502
D-Link DGS-3312SR Product Manual preview
DGS-3312SR
Brand: D-Link Pages: 244
D-Link GO-SW-5G User Manual preview
GO-SW-5G
Brand: D-Link Pages: 20
D-Link DES-1008E Quick Install Manual preview
DES-1008E
Brand: D-Link Pages: 2
D-Link KVM-440 User Manual preview
KVM-440
Brand: D-Link Pages: 37
D-Link DES-1018DG Quick Installation Manual preview
DES-1018DG
Brand: D-Link Pages: 28
Cabletron Systems SmartCell 6A000 User Manual preview
SmartCell 6A000
Brand: Cabletron Systems Pages: 114
Cabletron Systems MRX Installation Manual preview
MRX
Brand: Cabletron Systems Pages: 62
Cabletron Systems CyberSWITCH CSX150 Quick Start Manual preview
CyberSWITCH CSX150
Brand: Cabletron Systems Pages: 49
Cabletron Systems Cabletron CyberSWITCH CSX5500 User Manual preview
Cabletron CyberSWITCH CSX5500
Brand: Cabletron Systems Pages: 729
Campbell SDS-122 Instruction Manual preview
SDS-122
Brand: Campbell Pages: 14
Cabletron Systems SmartSwitch 6500 Installation And Setup Manual preview
SmartSwitch 6500
Brand: Cabletron Systems Pages: 62
CZHOON CZH-T287 User Manual preview
CZH-T287
Brand: CZHOON Pages: 4
FCI FLT93 Series Installation, Operation, Maintenance And Troubleshooting preview
FLT93 Series
Brand: FCI Pages: 12
3onedata ES1026-2F Quick Installation Manual preview
ES1026-2F
Brand: 3onedata Pages: 2

Brands by name

Popular brands

Load more brands