Cisco BTS 10200 Troubleshooting Manual Download Page 45

Page: 45 / 62

4-3

Cisco BTS 10200 Softswitch ISDN Provisioning and Troubleshooting

OL-12436-02

Chapter 4 Maintaining and Troubleshooting the ISDN System

Status and Control Commands

Table 4-2

describes the D-channel NFAS operational status to status output mappings.

Syntax Description

See the

Cisco BTS 10200 Softswitch Command Line Interface Guide for Call Processing

, Chapter 6,

ISDN D-Channel section for token information.

DCHAN_DOWN_IUA_INACTIVE_HARD_

NORMAL

ISDN D-Channel down IUA layer inactive hard
normal

DCHAN_DOWN_ESTABLISH_REQ_SOFT_

NORMAL

ISDN D-Channel down establish request soft
normal

DCHAN_DOWN_ESTABLISH_REQ_HARD_

NORMAL

ISDN D-Channel down establish request hard
normal

DCHAN_DOWN_ESTABLISH_FAIL_SOFT_

NORMAL

ISDN D-Channel down establish fail soft normal

DCHAN_DOWN_ESTABLISH_FAIL_HARD_N
ORMAL

ISDN D-Channel down establish fail hard normal

DCHAN_REMOVE_RELEASE_REQ

ISDN D-Channel remove release request

DCHAN_REMOVE_SESSION_SET_REQ

ISDN D-Channel remove session set request

DCHAN_REMOVE_SCTP_ASSOC_REQ

ISDN D-Channel remove SCTP association
request

ISDN_DCHAN_REMOVE_GRACEFUL

ISDN D-Channel remove gracefully

Table 4-1

D-Channel Operational Status to Status Output Mapping (continued)

D-Channel Operational Status

Status Output

Table 4-2

D-Channel NFAS Operational Status to Status Output Mapping

D-Channel NFAS Operational Status

Status Output

ISDN_DCHAN_STATE_MOOS

ISDN D-Channel is Manual Out-of-Service

ISDN_DCHAN_STATE_SESSION_DOWN

ISDN D-Channel is Backhaul Session Down

ISDN_DCHAN_STATE_SESSION_UP

ISDN D-Channel is Backhaul Session Up

ISDN_DCHAN_STATE_OOS

ISDN D-Channel is Out-of-Service

ISDN_DCHAN_STATE_ESTB_REQ

ISDN D-Channel sent Establish Request

ISDN_DCHAN_STATE_REL_REQ

ISDN D-Channel sent Release Request

ISDN_DCHAN_STATE_IS

ISDN D-Channel is In-Service

ISDN_DCHAN_STATE_MB

ISDN D-Channel is Maintenance Busy

ISDN_DCHAN_STATE_WAIT

ISDN D-Channel is in Wait for Service Ack

ISDN_DCHAN_STATE_STBY

ISDN D-Channel is Standby

ISDN_DCHAN_STATE_CREATE_SCTP_ASSOC

ISDN D-Channel create SCTP Assoc Request

ISDN_DCHAN_STATE_SCTP_ASSOC_ESTB

ISDN D-Channel SCTP Assoc Established

ISDN_DCHAN_STATE_DELETE_SCTP_ASSOC

ISDN D-Channel delete SCTP Assoc Request

Summary of Contents for BTS 10200































































Search results

Summary of Contents for BTS 10200

Reviews:

Related manuals for BTS 10200

Brands by name

Popular brands

Cisco BTS 10200, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200

Reviews:

Related manuals for BTS 10200

Brands by name

Popular brands