Cisco BTS 10200 Troubleshooting Manual Download Page 15

Page: 15 / 62

1-9

Cisco BTS 10200 Softswitch ISDN Provisioning and Troubleshooting

OL-12436-02

Chapter 1 ISDN Provisioning

Cisco BTS 10200 Provisioning

Figure 1-7

Sample Configuration for NFAS

Add the ISDN D-channel profile with the nfas-supp token set to Y.

add isdn-dchan-profile id=NI2; description=dallas isdn dchan profile no.1;

type=swv-us-ni2-pri; interface-type=network; isdn-restart-pri-supp=y;

isdn-restart-interface-supp=y;isdn-service-supp=n; isdn-restart-chan-supp=y;

isdn-farend-init=n;isdn-query-supp=n;nfas-supp=y; bchan-neg-supp=y; t-301=300;

t-302=10; t-303=4; t-305=30;t-308=4; t-309=90;t-310=10; t-316=30; t-321=20;t-322=4;

t-323=30;

Add the ISDN interfaces.

add isdn-intf isdn-dchan-id=100; intf=0;

add isdn-intf isdn-dchan-id=100; intf=1;

add isdn-intf isdn-dchan-id=100; intf=2;

Add the primary and backup ISDN D channels using the session set ID added in Step 2c and the
ISDN interfaces added in Step 4b.

add isdn-dchan id=100; backhaul-type=RUDP; set-id=backset1; dchan-slot=0;

dchan-port=0; dchan-type=primary; dchan-intf=0; isdn-dchan-profile-id=NI2;

add isdn-dchan id=100; backhaul-type=RUDP; set-id=backset1; dchan-slot=0;

dchan-port=1; dchan-type=backup; dchan-intf=1; isdn-dchan-profile-id=NI2;

Add an ISDN trunk group profile.

add isdn-tg-profile id=dallas1; chrg-num-supp=Y;

Add the ISDN trunk groups using the ISDN trunk group profile added in Step 4d.

add trunk-grp id=100;call-agent-id=CA146; tg-type=ISDN; tg-profile-id=ISDN;

pop-id=1;glare=ALL;mgcp-pkg-type=T; dial-plan-id=dp1;isdn-dchan-id=100;

Add the ISDN terminations using the MGW added in Step 2b.

add termination prefix=s0/ds1-0/; port-start=1; port-end=23; type=trunk;

mgw-id=mgw_isdn;

add termination prefix=s0/ds1-1/; port-start=1; port-end=23; type=trunk;

mgw-id=mgw_isdn;

add termination prefix=s0/ds1-2/; port-start=1; port-end=24; type=trunk;

mgw-id=mgw-isdn;

Primary D Channel

Backup D Channel

Trunk group (100)

Interface - 1

Interface - 2

CIC start - 1

CIC start - 24

CIC end - 23

CIC end - 70

CIC start - 47

CIC end - 46

Interface - 0

69721

23 24

Summary of Contents for BTS 10200































































Search results

Summary of Contents for BTS 10200

Reviews:

Related manuals for BTS 10200

Brands by name

Popular brands

Cisco BTS 10200, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200

Reviews:

Related manuals for BTS 10200

Brands by name

Popular brands