Cisco ASR-920-12SZ-IM Quick Start Manual Download Page 18 | Manualshive

Page: 18 / 25

background image

Install the AC Power Cables

To install the AC power cables in the power supply slots:

Procedure

Step 1

Plug the power supply cord in the power supply module.

Step 2

Insert the power supply cord into the tie [1,3] and tighten the tie around the power supply cord as shown in [2,4] in the
figure below.

Figure 14: Attach the AC Power Tie-and-Clip Cord

These images are for only representation purposes. Certain variants of Cisco NCS 540 do not include a tie for
the power supply cord.

Note

Activate an AC Power Supply Module

Perform the following procedure to activate an AC power supply:

18

«
...
16
17
18
19
20
...
»

Summary of Contents for ASR-920-12SZ-IM


























Reviews:

No comments

Related manuals for ASR-920-12SZ-IM

Brand: Campbell Pages: 42

Brand: Datasheen Pages: 25

Brand: D-Link Pages: 83

Brand: Edge-Core Pages: 7

Brand: ADTRAN Pages: 9

Brand: ForeScout Pages: 28

Brand: Watchguard Pages: 40

Storage Networking (Unified Fabric Pilot)

Brand: Qlogic Pages: 76

Brand: ZoneVu Pages: 15

Brand: Alcatel Pages: 4

Brand: Netopia Pages: 138

Brand: R.V.R. Elettronica Pages: 171

Brand: Altronix Pages: 8

Brand: Ryobi Pages: 84

Brand: Enterasys Pages: 808

PDG-DET100L - SXGA+ DLP Projector

Brand: Sanyo Pages: 1

ECO-i SHA-LN16UAB

Brand: Sanyo Pages: 1

Brand: Sanyo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands