Cisco ASR 901S Series Installation Manual Download Page 48

Page: 48 / 106

Step 8

Hand-tighten the bolts and the nut (do not overtighten).

Step 9

Adjust the top edge of the mounting bracket until it is horizontal and tighten the screws and the flange nut to
13 to 15 ft lbs (17.6 to 20.3 Nm).

Step 10

Position the two screws on either side of the router with the bolt holes on the mounting bracket (see the
following figure).

The router should be positioned with the LEDs on the bottom to allow viewing from the ground.

Note

Figure 18: Mounting the Router onto the Mounting Bracket on the Pole

Pole

M8 x 12 screws

Metal straps

M8 spring washers

—

Mounting bracket

Cisco ASR 901S Series Aggregation Services Router Hardware Installation Guide

OL-29732-01

Installing the Router

Mounting the Router onto a Pole

Summary of Contents for ASR 901S Series











































































































Search results

Summary of Contents for ASR 901S Series

Reviews:

Related manuals for ASR 901S Series

Brands by name

Popular brands

Cisco ASR 901S Series, Installation Manual

Search results

Summary of Contents for ASR 901S Series

Reviews:

Related manuals for ASR 901S Series

Brands by name

Popular brands