manualshive.com logo in svg

Cisco ASR 9000 Series, Installation Manual

The Cisco ASR 9000 Series is a cutting-edge networking solution, offering unmatched performance and reliability. To streamline the installation process, it comes with a comprehensive Installation Manual available for free download from our website, empowering users with step-by-step instructions to maximize the potential of this exceptional product.

Share
Download
background image

The length of the cables depends on the location of your router in relation to the source of DC power. These
cables and the cable lugs used to attach the cables to the router chassis are not available from Cisco Systems.
They are available from any commercial cable vendor. For more information on site power and source DC
cable requirements, see

Power Connection Guidelines, on page 27

.

Note

To ensure that power remains off while you are performing this procedure, lock-out/tag-out the DC circuit
breaker switch in the off (0) position until you are ready to turn it on.

Caution

Follow these steps to connect the DC source power cables to a DC power tray:

Procedure

Step 1

Verify that the power tray switch is set to the STANDBY (0) position.

Step 2

Remove the clear plastic safety covers that fit over the DC power connection terminal studs.

Step 3

Connect the DC power cables in the following order (see

Figure 192: Typical AC Power Connections to an

AC Power Tray—Version 1 Power System, on page 192

for the version 1 power system,

Figure 195: Typical

Power Connections to a Power Tray for a Single DC Power Module—Version 2 Power System, on page 194

for

the version 2 power system, and

Figure 196: Typical Power Connections to a Power Tray for a Single DC

Power Module—Version 3 Power System, on page 195

for the version 3 power system.

a) Ground cables first.
b) Positive cables next.
c) Negative cable last.

Step 4

Repeat Step 3 for the other power modules installed in the tray.

To prevent injury and damage to the equipment, always attach the ground and source DC power
cable lugs to power tray terminals in the following order: (1) ground to ground, (2) positive (+) to
positive (+), (3) negative (–) to negative (–).

Caution

Do not overtighten the nuts that secure the DC power cables to the power tray terminals. Using the
7/16 hex socket and torque wrench the nuts should be tightened to a torque of 45 to 50 in-lb.

Caution

Cisco ASR 9000 Series Aggregation Services Router Hardware Installation Guide

193

Installing Cards and Modules in the Chassis

Connecting Power to a DC-Powered Router

Summary of Contents for ASR 9000 Series





























































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Ubisys G1 Assembly And Commissioning Instructions preview
G1
Brand: Ubisys Pages: 51
OlenCom MG-iP Series Reference Manual preview
MG-iP Series
Brand: OlenCom Pages: 299
San Telequip SC10E4M K User Manual preview
SC10E4M K
Brand: San Telequip Pages: 19
Anybus AB7702 Installation Manual preview
AB7702
Brand: Anybus Pages: 2
Pace 4111N Manual preview
4111N
Brand: Pace Pages: 2
JBM electronics C120F Quick Start Manual preview
C120F
Brand: JBM electronics Pages: 29
ZyXEL Communications G.SHDSL.bis 4-port Security Gateway P-793H User Manual preview
G.SHDSL.bis 4-port Security Gateway P-793H
Brand: ZyXEL Communications Pages: 444
SpectraLink NetLink 150 Technical Bulletin preview
NetLink 150
Brand: SpectraLink Pages: 2
Watts 64129 User Manual preview
64129
Brand: Watts Pages: 108
Toro Tempus Air BW User Manual preview
Tempus Air BW
Brand: Toro Pages: 40
Elko SmartHUB EKO07235 Manual preview
SmartHUB EKO07235
Brand: Elko Pages: 4
Elko iNELS AirGTW-FWD Quick Start Manual preview
iNELS AirGTW-FWD
Brand: Elko Pages: 12
eQ-3 MAX! Cube Operating Manual preview
MAX! Cube
Brand: eQ-3 Pages: 44
Aruba EC-10104 Installation Manual preview
EC-10104
Brand: Aruba Pages: 20
Planet WPG-120 Quick Installation Manual preview
WPG-120
Brand: Planet Pages: 2
Planet Networking & Communication Hot Spot WSG-403 User Manual preview
Hot Spot WSG-403
Brand: Planet Networking & Communication Pages: 125
Inovonics E 4080 Series Quick Start Manual preview
E 4080 Series
Brand: Inovonics Pages: 13
Tut Systems SMS2000 User Manual preview
SMS2000
Brand: Tut Systems Pages: 104

Brands by name

Popular brands

Load more brands