Cisco ASR 5500 System Administration Manual Download | Manualshive

Page: 98 / 430

background image

•

ip_address

and

netmask

are the IP address and subnet mask of the target network. This IP address can

be entered using IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

•

gw_address

is the IP address of the default gateway or next-hop route. This IP address can be entered

using IPv4 dotted-decimal or IPv6 colon-separated-hexadecimal notation.

•

To configure a route to the gateway router, use 0.0.0.0 for the network and mask variables.

•

Repeat as needed. Multiple static routes can be configured to the same destination to provide an alternative
means of communication in case the preferred route fails.

Viewing and Verifying Port Configuration

Step 1

Verify that your interface configuration settings are correct by entering the following commands:

[local]

host_name

#

context context_name

[

context_name

]

host_name

#

show { ip | ipv6 } interface

context_name

represents the name of the context in which the interface was created. The output from these commands

should be similar to the following example.

In this example an interface named

mgmt1

was configured in the local context.

Example:

In this example an interface named

mgmt1

was configured in the local context.

Intf Name:

mgmt1

Intf Type:

Broadcast

IP State:

UP (Bound to 10/11 untagged, ifIndex 285278209)

IP Address:

192.168.100.3

Subnet Mask:

255.255.255.0

Bcast Address:

192.168.100.255

MTU:

1500

Resoln Type:

ARP

ARP timeout:

3600 secs

Number of Secondary Addresses:

0

Total interface count:

1

Step 2

Verify that your port configuration settings are correct by entering the following command:

[

context_name

]

host_name

#

show configuration port slot#/port#

Step 3

Verify that your static route(s) was configured properly by entering the following command:

[

context_name

]

host_name

#

show ip static-route

Step 4

Save the configuration as described in the

Verifying and Saving Your Configuration

chapter.

VLANs

Virtual LANs (VLANs) allow two logically separated networks to use the same physical medium. VLAN
segmentation, also called 802.1q tagging, works by appending a tag identifying the VLAN ID to each Ethernet
frame.

For information on how to create VLANs to handle specific packet types, see the

VLANs

chapter.

ASR 5500 System Administration Guide, StarOS Release 21.5

72

System Interfaces and Ports

Viewing and Verifying Port Configuration

«
...
96
97
98
99
100
...
»

Summary of Contents for ASR 5500















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 5500

Brand: National Instruments Pages: 4

Brand: Accuride Pages: 2

BlackDiamond X8 Series

Brand: Extreme Networks Pages: 120

Brand: Gigabyte Pages: 12

Network Convergence System 6000 Fabric Card Chassis

Brand: Cisco Pages: 202

Nexus 3000 series

Brand: Cisco Pages: 356

Brand: Cisco Pages: 34

Brand: Cisco Pages: 402

Brand: Cisco Pages: 508

Brand: Cisco Pages: 12

NCS 4000 Series

Brand: Cisco Pages: 82

Brand: Cisco Pages: 85

Brand: Supermicro Pages: 72

Brand: Sencore Pages: 2

Brand: LevelOne Pages: 10

Brand: iStarUSA Pages: 3

Brand: iStarUSA Pages: 3

Brand: iStarUSA Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands