background image

 

6  

 

IC Statement   

This device complies with Industry Canada license-exempt RSS standard(s). Operation 
is subject to the following two conditions: (1) this device may not cause interference, and 
(2) this device must accept any interference, including interference that may cause 
undesired operation of the device. 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts 
de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire 
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si 
le brouillage est susceptible d'en compromettre le fonctionnement.

 

 
 

For product available in the USA/Canada market, only channel 1~11 can be operated. 
Selection of other channels is not possible. 

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être 
exploités. Sélection d'autres canaux n'est pas possible. 

 
 

This device and its antenna(s) must not be co-located with any other transmitters except in 
accordance with IC multi-transmitter product procedures. 
Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated 
simultaneously without reassessment permissive change. 

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une 
autre antenne ou transmetteur. 

 
 

Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 
MHz, 
5470-5600 MHz and 5650-5725 MHz 

Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 
MHz, 5470-5600 MHz et 5650-5725 MHz 

 
 

The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for 
harmful interference to co-channel mobile satellite systems. 

les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une 
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites 
mobiles utilisant les mêmes canaux. 

 
 

Summary of Contents for ASA5506-AP702










Reviews: