background image

 

4  

 

 

FCC Statement: 

Federal Communication Commission Interference Statement 

 

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one of the following measures: 

   

Reorient or relocate the receiving antenna. 

   

Increase the separation between the equipment and receiver. 

   

Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 

   

Consult the dealer or an experienced radio/TV technician for help. 

 
 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation. 

 
 

For product available in the USA/Canada market, only channel 1~11 can be operated. 
Selection of other channels is not possible. 
 
 

This device and its antenna(s) must not be co-located with any other transmitters except in 
accordance with FCC multi-transmitter product procedures. 
Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated 
simultaneously without C2P.  

 
 

This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in 
indoor environment only. 
 
 
Devices will not permit operations on channels 120-132 for 11a and 11n/a which overlap 
the 5600 - 5650 MHz band. 
 

Summary of Contents for ASA5506-AP702










Reviews: