Cisco AS5350 - Universal Access Server Configuration Manual Download Page 52

Page: 52 / 262

3-8

Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide

OL-3418-02 B0

Chapter 3

Basic Configuration Using the Command-Line Interface

Configuring the Asynchronous Group Interface

Async4/00 is down, line protocol is down

modem(slot/port)=4/0, state=IDLE

dsx1(slot/unit/channel)=NONE, status=VDEV_STATUS_UNLOCKED

Hardware is Async Serial

MTU 1500 bytes, BW 115 Kbit, DLY 100000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation SLIP, loopback not set

DTR is pulsed for 5 seconds on reset

Last input never, output never, output hang never

Last clearing of "show interface" counters never

Input queue: 0/10/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: weighted fair

Output queue: 0/1000/64/0 (size/max total/threshold/drops)

Conversations 0/1/32 (active/max active/max total)

Reserved Conversations 0/0 (allocated/max allocated)

Available Bandwidth 86 kilobits/sec

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

Tip

If you are having trouble:

•

Enter the show async status command to check for errors and local and remote addresses:

AS5400# show async status

Async protocol statistics:

Int Local Remote Qd InPack OutPac Inerr Drops MTU

1/00 42.1.1.1 None 0 0 0 0 0 1500

1/01 192.168.10.100 None 0 0 0 0 0 1500

1/02 192.168.10.100 None 0 0 0 0 0 1500

1/03 192.168.10.100 None 0 0 0 0 0 1500

1/04 192.168.10.100 None 0 0 0 0 0 1500

1/05 192.168.10.100 None 0 0 0 0 0 1500

4/52 192.168.10.100 None 0 0 0 0 0 1500

*6/00 192.168.10.100 34.6.42.1 0 130 50 5 0 1500

*6/01 192.168.10.100 34.6.92.1 0 131 53 5 0 1500

*6/02 192.168.10.100 34.5.92.1 0 130 50 5 0 1500

*6/03 192.168.10.100 34.4.14.1 0 116 40 4 0 1500

*7/102 192.168.10.100 34.1.89.1 0 119 40 4 0 1500

*7/103 192.168.10.100 34.4.34.1 0 118 40 4 0 1500

*7/104 192.168.10.100 34.1.67.1 0 105 40 4 0 1500

7/105 192.168.10.100 None 0 0 0 0 0 1500

*7/106 192.168.10.100 34.4.90.1 0 119 40 4 0 1500

*7/107 192.168.10.100 34.1.42.1 0 119 40 4 0 1500

Rcvd: 25762 packets, 1052214 bytes

0 format errors, 891 checksum errors, 0 overrun

Sent: 8891 packets, 222264 bytes, 0 dropped

Summary of Contents for AS5350 - Universal Access Server







































































































































































































































































Search results

Summary of Contents for AS5350 - Universal Access Server

Reviews:

Brands by name

Popular brands

Cisco AS5350 - Universal Access Server, Configuration Manual

Search results

Summary of Contents for AS5350 - Universal Access Server

Reviews:

Brands by name

Popular brands