manualshive.com logo in svg

Cisco AS5350 - Universal Access Server, Configuration Manual

Share
Download
Cisco AS5350 - Universal Access Server Configuration Manual Download Page 160

 

-10

Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide

OL-3418-02 B0

Appendix

Getting Started

Step 11

Enter yes to allow users to dial in via ISDN or analog modems.

Do you intend to allow users to dial in? [yes]: yes

There are 16 controllers on this access server. If you want to use

the full capacity of the access server configure all controllers.

Controller CT1 0,1,...etc  in software corresponds to Port 0,1,..etc

on the back of the access server.

PRI configuration can be configured to controllers all at once

based on your PRI controllers selection. Where as CAS configuration 

will be configured individually for each controller.

Step 12

Enter the number of controllers you will be using for the PRI configuration or press Enter to configure 
all controllers.

Enter # of controllers, you will be using for PRI configuration [16]:

Configuring controller parameters:

Step 13

Press Enter for every slot, port, and channel.

Configuring controller T1 1/0:

 Configuring PRI on this controller.

Configuring controller T1 1/1:

 Configuring PRI on this controller.

Configuring controller T1 1/2:

 Configuring PRI on this controller.

Configuring controller T1 1/3:

 Configuring PRI on this controller.

.

.

.

.

Configuring controller T1 2/6:

 Configuring PRI on this controller.

Configuring controller T1 2/7:

 Configuring PRI on this controller.

Configuring interface parameters:

Step 14

Enter yes to configure the FastEthernet0/0 interface to connect the gateway to a LAN, then respond to 
the remaining questions to configure the FastEthernet port.

Do you want to configure FastEthernet0/0  interface? [yes]: yes

  Use the 100 Base-TX (RJ-45) connector? [yes]:

Note

Full duplex mode enables simultaneous data transfer between a sending and a receiving station.

Summary of Contents for AS5350 - Universal Access Server







































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands